KDR â CaRTon LIvE SToRaGE SySTEM - SSI Schäfer
KDR â CaRTon LIvE SToRaGE SySTEM - SSI Schäfer
KDR â CaRTon LIvE SToRaGE SySTEM - SSI Schäfer
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>KDR</strong> Carton Live Storage<br />
Material handling fl ow beds and ergonomics<br />
Upper limit<br />
Picking zone<br />
500<br />
400<br />
Thanks to the adjusting slots in the side-section of each flow<br />
bed, it can be adjusted horizontally – without the use of tools –<br />
in order to provide an optimal picking curve from an ergonomic<br />
viewpoint.<br />
Height 1.800<br />
Ideal picking<br />
zone 800<br />
With the use of strong side-profiles and additional internal<br />
cross supports it is possible to supply depths of up to<br />
5,000 mm.<br />
700<br />
Depth of fl ow bed, up to 5,000 mm<br />
4 x 6,25 mm<br />
Upright profile section P 63/P 65<br />
Height adjustment – in increments of just<br />
6.25 mm – is carried out by using inserting<br />
clip K-VH1 to a slot in the upright and<br />
then turning through 180 degrees. This<br />
vertical fine adjustment – without the<br />
use of nuts or bolts – allows the incline<br />
to be set to an optimum angle at any<br />
time. Adjusting slots (of 25 mm) along<br />
the entire length of the side-profile permit<br />
ergonomic configuration of the flow bed,<br />
without any depth restrictions.<br />
Outer<br />
piece<br />
Height adjustment 4 x 12,5 mm<br />
Inner<br />
piece<br />
Upright profile sec. P 73/P 93/P 95<br />
Height adjustment in increments of just<br />
12.5 mm – is carried out by repositioning<br />
the outer and inner clips. This<br />
vertical line adjustment, without the use<br />
of bolts allows the incline to be set to<br />
an optimum angle at anytime. Adjusting<br />
slots (of 25 mm) along the entire length<br />
of the side-profile permit ergonomic<br />
configuration of the flow bed.<br />
Adjusting clip for upright profile section<br />
P 63/P 65<br />
The height of the flow bed can be adjusted –<br />
in increments of 6.25 mm – by attaching the<br />
adjusting clip to the punched slot on either<br />
the right or left hand side, and by rotating.<br />
Outer<br />
Inner<br />
Slotted support (outer and inner) for<br />
upright profile section P 63/P 65<br />
Positioned over the adjusting clip to allow<br />
easy front to back adjustment of the flow bed<br />
in order to obtain the most ergonomically<br />
favourable position.<br />
Adjusting clip (front) for upright profile<br />
P 73/P 93/P 95<br />
For supporting the flow bed in the front<br />
uprights (PR 600 system).<br />
Adjusting increments: 12.5 mm.<br />
Adjusting clip (rear and inner)<br />
with spacer<br />
The purpose of the spacer is to reduce the<br />
adjusting increments from 12.5 mm to<br />
6.25 mm. It is slotted into the clip in order to<br />
provide additional central support.<br />
16