Tool Product Catalog - Duro Dyne

More documents

Recommendations

Info

File and Rasp Facts The following information is included to help you make the right choice of file to meet your particular requirements. File Terminology: Length Length is measured exclusive of tang, from point to heel. Desired stroke, length, type of material and its size will determine length required. Tang Heel Belly Point Length Shape Area to be filed will determine specific cross section - round, square, knife, flat, etc - to be used Coarseness Work to be accomplished, roughing or finishing, will determine type of teeth and coarseness for each application. Most American pattern files are available with 3 grades of cut: bastard-cut, second-cut and smooth- cut. Swiss pattern files are available in seven cuts: 00, 0, 1, 2, 3, 4, 6. The degree of coarseness is greater in longer files, but differences between bastard, second cut and smooth are proportionate. American Pattern Bastard Cut Second Cut Smooth Cut 00 0 1 2 3 4 6 Kinds of Teeth: Single-cut Single set of parallel, diagonal rows of teeth. Single-cut files are often used with light pressure to produce a smooth surface finish or to put a keen edge on knives, shears or saws. Double-cut Two sets of diagonal rows of teeth. The second set of teeth is cut in the opposite diagonal direction and on top of the first set. The first set of teeth is known as the overcut while the second is called the upcut. The upcut is finer than the overcut. The double-cut file is used with heavier pressure than the single-cut and removes material faster from the workplace. Rasp-cut Series of individual teeth which are formed by a single-pointed tool. This produces a rough cut that is used primarily on wood, hooves, aluminum and lead. Curved-cut Teeth are arranged in curved contours across the file face. The curved-cut file is normally used in automotive body shops for smoothing body panels. 32
Cross Reference Chart For Hacksaw Blades Dimensions Teeth L x W x T Per DURO DYNE Description Material In Inches Inch LENNOX MALCO MILWAUKEE USE 846106 62807-NF1024 Bi-Metal 10 x 1/2 x .025 24 20111-024HE N/A N/A for cross section 1/16" 20141-V024HE through 1/4" such as pipe, 220151-S024HE angles, small drill rod 846109 62825-NF1218 Bi-Metal 12 x 1/2 x .025 18 20116-218HE 1218B 48-43-0610 for general shop use 20144-V218HE 20154-S218HE 846110 62825-NF1224 Bi-Metal 12 x 1/2 x .025 24 120117-224HE 224B 48-43-0620 for cross section 1/16" 20145-V224HE through 1/4” such as pipe, 20155-S224HE angles, small drill rod 846111 62837-NF1232 Bi-Metal 12 x 1/2 x .025 32 20118-232HE 1232B 48-43-0630 for cross section up to 1/16" 20146-V232HE such as light tubing, 20156-S232HE sheet metal, BX 33 Hand Hacksaw Tooth Selector Strokes Material Teeth Per Minute Strokes Material Teeth Per Minute Non-Ferrous Ferrous Aluminum 14 60 *BX 32 60 Brass and Bronze 14-24 60 *Conduit, Rigid 24 60 *Brass Tubing 24 60 Drill Rod 18-24 60 Copper 14 60 Iron, Cast 14 60 Structural Shapes 14-24 60 *Pipe 24 60 Rails 14 60 Non-Metals Asbestos 14 60 *Sheet Metal 24-32 60 Steel, Machinery 14-18 60 Fiber 14 60 Steel, <strong>Tool</strong> 18-24 60 Slate 14 50 Structural Shapes, Heavy 18 60 *Special shatterproof blades of coarser teeth than specified Structural Shapes, Light 24 60 may be used with excellent results on thin sections. *Tubing, Light 32 60
Page 2 and 3: ABOUT DURO DYNE Established in 1952
Page 4 and 5: ACCESSORY TOOLS Dividers Heavy duty
Page 6 and 7: Twin End Drill Bits Twin end bits i
Page 8 and 9: Mini-Hacksaw This is an ergonomic h
Page 10 and 11: HVAC TOOLS 3-Blade Hand Crimper An
Page 12 and 13: RWK-14 Replacement Blade - Rapid-Ch
Page 14 and 15: Locking Pliers & Clamps With Chrome
Page 16 and 17: Slip Joint Pliers This combination
Page 18 and 19: No. 25 Handle for Reversible Round
Page 20 and 21: 90˚ Snips The 90˚ angle of the bl
Page 22 and 23: Straight Pattern Snips Straight pat
Page 24 and 25: Water Cooled Arms with Tips Arms ar
Page 26 and 27: 700 Series Magnetic End Hook The ma
Page 28 and 29: WIRE STRIPPERS & CUTTERS Crescent W
Page 30 and 31: Grinding Twist Drills Most drill tr
Page 34 and 35: Hacksaw Information Hand Hacksaw Bl
Page 36 and 37: Choosing the Correct Nutdriver Hex
Page 38 and 39: Helpful Hints When Using Reciprocat
Page 40 and 41: Choosing the Correct Screwdriver Ph
Page 42 and 43: Soldering Information Wire Numbers
Page 44 and 45: Torque Wrench Chart Bolts Grade Mar
Page 46 and 47: Metric Conversion Chart M = Millime
Page 48: ® © 2009 Duro Dyne Corp. Printed

Tool Product Catalog - Duro Dyne

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?