SolidCAM 2011

More documents

Recommendations

Info

Anti Vibration Techniques Tool diameter Number of flutes Helix angle Depth of cut ACPs = Axial Contact Points 4.5 ACPs 4 ACPs 3 ACPs 2 ACPs 2 ACPs Perfect Depth Many Contact Points
The best tool path! Morphing spirals Intelligent separation Reduced programming time Best user interface Reduced cycle times First part success Automatic speeds and feeds
Page 1 and 2:
SolidCAM 2011 What’s New
Page 3 and 4:
Improvement in selection speed (hig
Page 5 and 6:
Improvement in geometry synchroniza
Page 7 and 8:
Improvement in SolidCAM settings
Page 9 and 10:
New: Toolbox cycles
Page 11 and 12:
Toolbox - strategies • Simple cor
Page 13 and 14:
New: Machine ID definition • Comp
Page 15 and 16:
New: Machine Control operation •
Page 17 and 18:
Tool Table • New interface of Too
Page 19 and 20:
Turning tools: composite, drilling,
Page 21 and 22:
Turrets definition • Rotary turre
Page 23 and 24:
Milling tool Mounting • For Rotar
Page 25 and 26:
Tool change position • Possibilit
Page 27 and 28:
Custom setup of STL holder • Hold
Page 29 and 30:
Tool path editor for HSR/HSM • To
Page 31 and 32:
2.5D milling - Improve Profile Link
Page 33 and 34:
Transformation with and without M-c
Page 35 and 36:
New: HSR (High Speed Roughing) •
Page 37 and 38:
New: HSR/HSM (Separate links calcul
Page 39 and 40:
HSM - Fillets • Add the Basic opt
Page 41 and 42:
Improve link in HSM to sim 5x - Rel
Page 43 and 44:
SolidCAM 2011 - What’s New Stock
Page 45 and 46:
Fixture definition • Single dialo
Page 47 and 48:
SolidCAM 2011 - What’s New New Tu
Page 49 and 50:
New Turning operation: CutOff • N
Page 51 and 52: New turning operation: Sim. 4x Turn
Page 53 and 54: Enhancements of turning operation -
Page 59 and 60: Enhancements of link in turning ope
Page 61 and 62: Enhancements of link in turning ope
Page 63 and 64: Enhancements of Drilling operation
Page 65 and 66: Enhancements of threading operation
Page 67 and 68: Enhancements of threading operation
Page 69 and 70: SolidCAM 2011 - What’s New Enhanc
Page 71 and 72: Enhancements of grooving operation
Page 73 and 74: SolidCAM 2011 - What’s New Multi-
Page 75 and 76: Multi-Turret timeframe • Turret S
Page 77 and 78: Limitations control • Detection o
Page 79 and 80: iMachining Goals 1 2 Simplified Use
Page 81 and 82: 3 Problems with Typical Standard To
Page 83 and 84: iMachining’s Intelligent Tool Pat
Page 85 and 86: iMachining - Complete Controlled St
Page 87 and 88: iMachining - No Air Cutting Machine
Page 89 and 90: 3 Problems with Standard Tool Paths
Page 91 and 92: Entire Part Using iMachining
Page 93 and 94: 2 Features Only Found in iMachining
Page 95 and 96: Morphing Spirals After Separation M
Page 97 and 98: Optimal Speeds and Feeds by the Tec
Page 99 and 100: #1 Chip Thickness Chip Load at 90 D
Page 101: #2 Speed and Feed Adjustment
Page 106: SolidCAM 2011 What’s New
show all

SolidCAM 2011

Create successful ePaper yourself

Delete template?

Save as template?