SolidCAM 2011

More documents

Recommendations

Info

2.5D milling – Profile/Pocket - Improve Keep tool down Improve Keep tool down in: • Links between passes • Links between chains by providing 2 types of links: o Through Safety distance o Through Clearance level Keep tool down by <strong>SolidCAM</strong> Professor >>
Transformation with and without M-codes Use M-codes => @rotate/mirror Don’t Use M-codes => transformed coordinates
Page 1 and 2: SolidCAM 2011 What’s New
Page 3 and 4: Improvement in selection speed (hig
Page 5 and 6: Improvement in geometry synchroniza
Page 7 and 8: Improvement in SolidCAM settings
Page 9 and 10: New: Toolbox cycles
Page 11 and 12: Toolbox - strategies • Simple cor
Page 13 and 14: New: Machine ID definition • Comp
Page 15 and 16: New: Machine Control operation •
Page 17 and 18: Tool Table • New interface of Too
Page 19 and 20: Turning tools: composite, drilling,
Page 21 and 22: Turrets definition • Rotary turre
Page 23 and 24: Milling tool Mounting • For Rotar
Page 25 and 26: Tool change position • Possibilit
Page 27 and 28: Custom setup of STL holder • Hold
Page 29 and 30: Tool path editor for HSR/HSM • To
Page 31: 2.5D milling - Improve Profile Link
Page 35 and 36: New: HSR (High Speed Roughing) •
Page 37 and 38: New: HSR/HSM (Separate links calcul
Page 39 and 40: HSM - Fillets • Add the Basic opt
Page 41 and 42: Improve link in HSM to sim 5x - Rel
Page 43 and 44: SolidCAM 2011 - What’s New Stock
Page 45 and 46: Fixture definition • Single dialo
Page 47 and 48: SolidCAM 2011 - What’s New New Tu
Page 49 and 50: New Turning operation: CutOff • N
Page 51 and 52: New turning operation: Sim. 4x Turn
Page 53 and 54: Enhancements of turning operation -
Page 59 and 60: Enhancements of link in turning ope
Page 61 and 62: Enhancements of link in turning ope
Page 63 and 64: Enhancements of Drilling operation
Page 65 and 66: Enhancements of threading operation
Page 67 and 68: Enhancements of threading operation
Page 69 and 70: SolidCAM 2011 - What’s New Enhanc
Page 71 and 72: Enhancements of grooving operation
Page 73 and 74: SolidCAM 2011 - What’s New Multi-
Page 75 and 76: Multi-Turret timeframe • Turret S
Page 77 and 78: Limitations control • Detection o
Page 79 and 80: iMachining Goals 1 2 Simplified Use
Page 81 and 82: 3 Problems with Typical Standard To
Page 83 and 84:
iMachining’s Intelligent Tool Pat
Page 85 and 86:
iMachining - Complete Controlled St
Page 87 and 88:
iMachining - No Air Cutting Machine
Page 89 and 90:
3 Problems with Standard Tool Paths
Page 91 and 92:
Entire Part Using iMachining
Page 93 and 94:
2 Features Only Found in iMachining
Page 95 and 96:
Morphing Spirals After Separation M
Page 97 and 98:
Optimal Speeds and Feeds by the Tec
Page 99 and 100:
#1 Chip Thickness Chip Load at 90 D
Page 101 and 102:
#2 Speed and Feed Adjustment
Page 103 and 104:
The best tool path! Morphing spiral
Page 106:
SolidCAM 2011 What’s New
show all

SolidCAM 2011

Create successful ePaper yourself

Delete template?

Save as template?