- Page 1 and 2:
SolidCAM 2011 What’s New
- Page 3 and 4:
Improvement in selection speed (hig
- Page 5 and 6:
Improvement in geometry synchroniza
- Page 7 and 8:
Improvement in SolidCAM settings
- Page 9 and 10:
New: Toolbox cycles
- Page 11 and 12:
Toolbox - strategies • Simple cor
- Page 13 and 14:
New: Machine ID definition • Comp
- Page 15 and 16:
New: Machine Control operation •
- Page 17 and 18:
Tool Table • New interface of Too
- Page 19 and 20:
Turning tools: composite, drilling,
- Page 21 and 22:
Turrets definition • Rotary turre
- Page 23 and 24:
Milling tool Mounting • For Rotar
- Page 25 and 26:
Tool change position • Possibilit
- Page 27 and 28:
Custom setup of STL holder • Hold
- Page 29 and 30:
Tool path editor for HSR/HSM • To
- Page 31 and 32:
2.5D milling - Improve Profile Link
- Page 33 and 34:
Transformation with and without M-c
- Page 35 and 36:
New: HSR (High Speed Roughing) •
- Page 37 and 38:
New: HSR/HSM (Separate links calcul
- Page 39 and 40:
HSM - Fillets • Add the Basic opt
- Page 41 and 42:
Improve link in HSM to sim 5x - Rel
- Page 43 and 44:
SolidCAM 2011 - What’s New Stock
- Page 45 and 46:
Fixture definition • Single dialo
- Page 47 and 48:
SolidCAM 2011 - What’s New New Tu
- Page 49 and 50:
New Turning operation: CutOff • N
- Page 51 and 52:
New turning operation: Sim. 4x Turn
- Page 53 and 54:
Enhancements of turning operation -
- Page 55 and 56: Enhancements of turning operation -
- Page 57 and 58: Enhancements of turning operation -
- Page 59 and 60: Enhancements of link in turning ope
- Page 61 and 62: Enhancements of link in turning ope
- Page 63 and 64: Enhancements of Drilling operation
- Page 65 and 66: Enhancements of threading operation
- Page 67 and 68: Enhancements of threading operation
- Page 69 and 70: SolidCAM 2011 - What’s New Enhanc
- Page 71 and 72: Enhancements of grooving operation
- Page 73 and 74: SolidCAM 2011 - What’s New Multi-
- Page 75 and 76: Multi-Turret timeframe • Turret S
- Page 77 and 78: Limitations control • Detection o
- Page 79 and 80: iMachining Goals 1 2 Simplified Use
- Page 81 and 82: 3 Problems with Typical Standard To
- Page 83 and 84: iMachining’s Intelligent Tool Pat
- Page 85 and 86: iMachining - Complete Controlled St
- Page 87 and 88: iMachining - No Air Cutting Machine
- Page 89 and 90: 3 Problems with Standard Tool Paths
- Page 91 and 92: Entire Part Using iMachining
- Page 93 and 94: 2 Features Only Found in iMachining
- Page 95 and 96: Morphing Spirals After Separation M
- Page 97 and 98: Optimal Speeds and Feeds by the Tec
- Page 99 and 100: #1 Chip Thickness Chip Load at 90 D
- Page 101 and 102: #2 Speed and Feed Adjustment
- Page 103 and 104: The best tool path! Morphing spiral