TRX 350 4x4 - 4 Wheel Online

More documents

Recommendations

Info

HONDA TRX 350 4x4Kit number: 25-1050COMPLETE WINCH KITLOCATION Pt:\R.T.NO. QTY. DESCRIPTION1 WNH3000A 1 WINCH MOUNT PLATE2 WNH3001A 1 WINCH ATTACHING BRACKET3 WNH3002 1 L-BRACE6 UC78 1 7/8” U-CLAMP7 UCS34 1 3/4" SPACER /U-CLAMP8 UC1 1 1" U-CLAMP9 UCS78 1 7/8" SPACER/U-CLAMP10 CB516-2 1 5/16” X 2" CARRIAGE BOLTLN516NY 1 5/16" LOCKNUT -NYLOCK11 CB516-1 1 5/16" X 1" CARRIAGE BOLTLN516NY 1 5/16” LOCKNUT -NYL.OCK13 FW516 1 5/16" FLATWASHER14 B38-1 1 3/8” X 1” BOLTSLN38NY 1 3/8” LOCKNUTS-NYLOCK15 B38-112 2 3/8” X 1-1/2” BOLTSLN38NY 2 3/8” LOCKNUTS-NYLOCK16 MB8-30 2 8mm x 30mm METRIC BOLTSLW516 2 5/16” LOCKWASHERSFW516 2 5/16" FLATWASHERSBagged Items6...UC78 (1) 7/8” U-Clamp7...UCS34 (1) 3/4” Spacer/U-ClampSPOOLSIDEMOTORSIDEFRONT2
HONDA TRX 350 4x4 WINCH ATTACHING KITASSEMBLY INSTRUCTIONS**Some components of this kit may be already assembled. All directions referring to right and left arewhen the rider is sitting on the machine. Please Note: The cable clamp, roller hawse, and cable stop areincluded with the winch.For use with the 1000 Lb. Winch only.1. Remove the two 8mm bolts that attach the lower brush guard support tube to each side ofthe front frame tube that the Serial No. is on. DO NOT REPLACE THESE BOLTS. They willbe replaced by 8mm x 30mm bolts.2. Remove the Winch Mount Plate from the Winch Attaching Bracket. NOTE: It is helpful toleave the 3/8" x 1-1/2" bolts in the Winch Attaching Bracket for now, hold them in place withthe locknuts.3. Using the two 8mm x 30mm bolts, lockwashers and flatwashers, attach the WinchAttaching Bracket to the ATV frame. NOTE: The flatwashers go between the AttachingBracket and the Brush Guard support tubes. FINGER TIGHTEN ONLY.4. Attach the Winch Unit to the Winch Mount Plate. Use the 3/8" x 1" bolt that is in the WinchMount Plate. NOTE: The bolt is in the proper hole and attaches to the front hole in the WinchUnit. Align the rear hole in the Winch Unit with the rear hole in the Mount Plate, hold in placeand TIGHTEN THE 3/8” x 1” BOLT SECURELY.5. Remove the nuts from the bolts that are in the Winch Attaching Bracket that you havealready mounted to the ATV. Motor end first, and up from the bottom, insert the Winch upand in front of the Winch Attaching Bracket. Rotate the Winch so that the rear Winch Mounthole and the hole in the Winch Mount Plate align on the bolts in the Attaching Bracket. Placethe locknuts on the bolts. DO NOT TIGHTEN COMPLETELY.6. Using the 5/16" x 1" carriage bolt, install the L-Brace to the Winch Mount Plate. NOTE: TheL-Brace mounts on top of the Mount Plate, DO NOT FULLY TIGHTEN THE CARRIAGE BOLT.1986 MODELS: On 1986 Models the 5/16" flatwasher may have to be placed between the L-Brace and the Winch Mount Plate to prevent the Winch Motor from contacting the ATV frame.7. Using the chart below, determine which U-Clamps and U-Clamp Spacers and whichmounting hole to use when bolting the Clamp to the L-Brace.1986 TRX350 7/8” CLAMP 3/4” SPACER TOP HOLE1987 TRX350 7/8” CLAMP 3/4” SPACER TOP HOLE1987 FOREMAN 1” CLAMP 7/8” SPACER BOTTOM HOLE1988 FOREMAN 1” CLAMP 7/8” SPACER TOP HOLE3
Page 1: HondaTRX 350 4x4WINCHMOUNT KITINSTA
Page 5 and 6: CAUTIONBE AWARE OF THE CABLE STOP C

TRX 350 4x4 - 4 Wheel Online

Create successful ePaper yourself

Delete template?

Save as template?