PRODUCT GUIDE MODEL 463247412 - Char-Broil Grills

More documents

Recommendations

Info

Ignitor Lighting (continued)8. For grills equipped with ELECTRONIC IGNITION ateach burner:Repeat steps 4 through 6 to light each burner.9. Once each burner has ignited, turn knobs to desired setting.WARNINGTurn controls and gas source or tank OFF when notin use.CAUTIONIf ignition does NOT occur in 5 seconds, turn theburner controls OFF, wait 5 minutes and repeat thelighting procedure. If the burner does not ignite withthe valve open, gas will continue to flow out of theburner and could accidently ignite with risk of injury.Match-LightingsDo not lean over grill while lighting.1. Open lid. Turn ON gas at LP cylinder.2. Place match into match holder (hanging from side panel ofgrill). Light match; then light burner by placing match throughthe match light hole on right or left side of grill.3. Push in and turn far right or far left burner knob to the HIposition, depending on match light hole selected. Be sureburner lights and stays lit.4. Light adjacent burners in sequence by pushing knobs in andturning to the HI position.NOTE: Your grill may NOT be equipped with a Sideburner!Sideburner Ignitor LightingsDo not lean over grill while lighting.1. Open sideburner lid. Turn ON gas at LP cylinder.2. Turn sideburner knob to the HI position, push and holdELECTRONIC IGNITOR button.3. If sideburner does NOT light within 5 seconds, turn knob to OFF,wait 5 minutes, thenrepeat lighting procedure.Sideburner Match Lighting1. Open sideburner lid. Turn ONgas at LP cylinder.2. Place lit match near burner.3. Turn sideburner knob to theHI position.Be sure burner lights andstays lit.8Burner Flame Check• Remove cooking grates and flame tamers. Light burners, rotateknobs from HI to LOW. You should see a smaller flame inLOW position than seen on HI. Perform burner flame checkon sideburner, also. Always check flame prior to each use. Ifonly low flame is seen refer to "Sudden drop or low flame" inthe Troubleshooting Section.HILOWTurning Grill Off• Turn all knobs to the OFFposition. Turn LP cylinder OFF by turninghand-wheel clockwise to a full stop.Ignitor Check• Turn gas off at LP cylinder. Press and hold electronic ignitorbutton. "Click" should be heard and spark seen each timebetween each collector box or burner and electrode. See"Troubleshooting" if no click or spark.Valve Check• Important: Make sure gas is off at LP cylinder beforechecking valves. Knobs lock in OFF position. To checkvalves, first push in knobs and release, knobs should springback. If knobs do not spring back, replace valve assemblybefore using grill. Turn knobs to LOW position then turn back toOFF position. Valves should turn smoothly.Hose Check• Before each use, check to see if hoses are cut or worn or kinked.Replace damaged hoses before using grill. Use onlyvalve/hose/regulator specified by manufacturer.General Grill Cleaning• Do not mistake brown or black accumulation of grease andsmoke for paint. Interiors of gas grills are not painted at thefactory (and should never be painted). Apply a strong solutionof detergent and water or use a grill cleaner with scrub brushon insides of grill lid and bottom. Rinse and allow to completelyair dry. Do not apply a caustic grill/oven cleaner to paintedsurfaces.• Plastic parts: Wash with warm soapy water and wipe dry.sDo not use citrisol, abrasive cleaners, degreasers or aconcentrated grill cleaner on plastic parts. Damage to andfailure of parts can result.• Porcelain surfaces: Because of glass-like composition, mostresidue can be wiped away with baking soda/water solution orspecially formulated cleaner. Use nonabrasive scouring powderfor stubborn stains.• Painted surfaces: Wash with mild detergent or nonabrasivecleaner and warm soapy water. Wipe dry with a softnonabrasive cloth.• Stainless steel surfaces: To maintain your grill’s high qualityappearance, wash with mild detergent and warm soapy waterand wipe dry with a soft cloth after each use. Baked-on greasedeposits may require the use of an abrasive plastic cleaningpad. Use only in direction of brushed finish to avoid damage.Do not use abrasive pad on areas with graphics.• Cooking surfaces: If a bristle brush is used to clean any ofthe grill cooking surfaces, ensure no loose bristles remain oncooking surfaces prior to grilling. It is not recommended toclean cooking surfaces while grill is hot.
CAUTIONSPIDER ALERT!SPIDER AND WEBSINSIDE BURNER TUBE3. Remove carryover tubes and burners.4. Detach electrode from burner.NOTE: Removal/Detachment method will depend on theburner configuration. See different configurations inillustrations below.5. Carefully lift each burner up and away from valve openings.We suggest three ways to clean the burner tubes. Use the oneeasiest for you.(A) Bend a stiff wire (a light weight coat hanger works well)into a small hook. Run the hook through each burnertube several times.If you notice that your grill is getting hard to light or that theflame isn’t as strong as it should be, take the time to check andclean the venturi’s.CONTROL PANELVALVESPIDER WEBSINSIDE VENTURIBURNERIn some areas of the country, spiders or small insects have beenknown to create “flashback” problems. The spiders spin webs, buildnests and lay eggs in the grill’s venturi tube(s) obstructing the flow ofgas to the burner. The backed-up gas can ignite in the venturi behindthe control panel. This is known as a flashback and it can damageyour grill and even cause injury.(B) Use a narrow bottle brush with a flexible handle (do notuse a brass wire brush), run the brush through eachburner tube several times.(C) Wear eye protection: Use an air hose to force air intothe burner tube and out the burner ports. Check eachport to make sure air comes out each hole.6. Wire brush entire outer surface of burner to remove foodresidue and dirt.7. Clean any blocked ports with a stiff wire such as an openpaper clip.8. Check burner for damage, due to normal wear and corrosionsome holes may become enlarged. If any large cracks orholes are found replace burner.VERY IMPORTANT: Burner tubes must reengage valveopenings. See illustrations at right.9. Attach electrode to burner.10. Carefully replace burners.11. Attach burners to brackets on firebox.12. Reposition carryover tubes and attachto burners. Replace flame tamers andcooking grates.Correctburner-to-valveengagementTo prevent flashbacks and ensure good performance the burner andventuri assembly should be removed from the grill and cleanedbefore use whenever the grill has been idle for an extended period.FireboxRemove screwsStoring Your Grill• Clean cooking grates.• Store in dry location.• When LP cylinder is connected to grill, store outdoors in a wellventilatedspace and out of reach of children.• Cover grill if stored outdoors. Choose from a variety of grillcovers offered by manufacturers.• Store grill indoors ONLY if LP cylinder is turned off anddisconnected, removed from grill and stored outdoors.• When removing grill from storage, follow “Cleaning the BurnerAssembly” instructions before starting grill.Cleaning the Burner AssemblyFollow these instructions to clean and/or replace parts of burnerassembly or if you have trouble igniting grill.1. Turn gas OFF at control knobs and LP cylinder.2. Remove cooking grates and flame tamers.FireboxCarryover tubeCarryover tubeFirebox burnerbracketFireboxburnerbracketElectrodeElectrodePry offelectrode witha flat bladescrewdriver9
Page 6: StraightHold coupling nut and regul
Page 11 and 12: PARTS LISTKey Qty DescriptionA 1 BO
Page 13 and 14: ASSEMBLY1Locking casterPlace bottom
Page 15 and 16: 5On back of grill, place upper back
Page 17 and 18: 8First, remove the two screws and l
Page 19 and 20: 12Inside of cart, insert rear shiel
Page 21 and 22: 16Place cooking grates onto the fir
Page 23 and 24: DANGER: If a gas leak cannot be sto
Page 25 and 26: Troubleshooting - Electronic Igniti
Page 27: Warranty Registration DepartmentP.O

PRODUCT GUIDE MODEL 463247412 - Char-Broil Grills

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?