APPROVED MATERIALS LIST (AML) - City of West Palm Beach

More documents

Recommendations

Info

Submittal:DUCTILE IRON PIPEDUCTILE IRON PIPE:Pipe shall comply with ANSI/AWWA Standard or latest revision. 3”, 10”, 14” and 16" pipe are considered “odd” sizesand may only be used to tie into existing lines. The minimum standards for 3” through 12" pressure pipe is Class 52.The minimum standard for 14” through 64" pressure pipe is Class 51. The minimum standard for all F. J. pipes, for anyusage, shall be Class 53. The minimum standard for all pipe size diameter sanitary collection system gravity mainsshall be Class 50 or Pressure Class 350.MANUFACTURER:____ American ____ Clow ____ U.S. Pipe ____ McWane ____ GriffinCLASS:Class 52, sizes to be used on water mains: _________________________Class 51, sizes to be used on water mains: _________________________Class 52, sizes to be used on force mains: _________________________Class 51, sizes to be used on force mains: _________________________Class 50, sizes to be used on gravity mains: ________________________Pressure Class 350, sizes to be used on gravity mains: _______________Class 53, sizes to be used for FJ pipe: ____________________________BELL TYPE:____FLANGE JOINTS:Flanges shall be ANSI Standard Class 125, plain faced and drilled, in accordance with ANSI B16.1. Flanges shall besolid with a uniform thickness as shown on Table 15.3 and Figure 15.1 of the ANSI/AWWA C115/A21.15 standard orlatest revision. Submit a letterhead correspondence from the manufacturer/vendor certifying that the flanged pipecomplies with ANSI/AWWA Flange standard, the ANSI/AWWA pipe standard and the ANSI/AWWA lining standard (iffor water) or the lining for gravity or force mains.____MECHANICAL JOINT:All mechanical joints shall conform to the latest edition of ANSI/AWWA C111/A21.11 standard.____SLIP OR PUSH-ON JOINT:All push-on type joints shall conform to the latest edition of ANSI/AWWA C111/A21.11 standard. The gasket materialshall be SBR type or equal.____RESTRAINED JOINT:All restrained joints shall conform to the latest edition of ANSI/AWWA C151 standard.- End of Section -Page 10 of 54 Approved Materials List – Revised November 1, 2011
Submittal:DUCTILE IRON LININGS AND COATINGSLININGS AND COATINGS FOR DUCTILE IRON PIPE AND FITTINGS:DISTRIBUTION SYSTEM WATER MAINS:INTERIOR:____ Cement Mortar Lining, per latest edition of ANSI/AWWA C104/A21.4 standard.____ Fusion-Bonded Epoxy Coating, per latest edition of ANSI/AWWA C116/A.21.16 standard.EXTERIOR:____ In-ground placement, bituminous asphalt coating required, per ANSI/AWWA C104/A21.4 standard or latestrevision.____ Fusion-Bonded Epoxy Coating, per ANSI/AWWA C116/A.21.16 standard.ENCASEMENT:____ Polyethylene Encasement, per the latest edition of ANSI/AWWA C105/A21.5 standard. Encasement shall bea minimum material thickness of 4 mil CL/HDPE.Fulton EnterprisesAmerican Ductile Iron Pipe CompanyU. S. Pipe CompanySANITARY SEWER COLLECTION GRAVITY MAINS, FORCE MAINS, and LATERALS (DIP):INTERIOR:____ PERMITEPermox PCS-9043, Glass Flake Epoxy____ VULCAN PAINTERS, INC.Protecto 401, Ceramic Epoxy Lining.NOTE: When DIP is utilized in wetwells and air release valve vaults, the interior coating for the wetwell or vault willalso be applied to the outside of the pipe.EXTERIOR:____ In-ground placement, Bituminous asphalt coating required, per the latest edition of ANSI/AWWA C104/A21.4standard.ENCASEMENT:____ Polyethylene Encasement, per the latest edition of ANSI/AWWA C105/A21.5 standard. Encasement shall bea minimum material thickness of 4 mil CL/HDPE.Fulton EnterprisesAmerican Ductile Iron Pipe CompanyU. S. Pipe CompanyCOATING CERTIFICATIONS:Certification letter must state the pipe and or fitting manufacturer to be used, the applicable ANSI/AWWAstandard, the coating to be used and the thickness of the coating.____ Shop for pipe (attach certification letter after this page)____ Shop for fittings (attach certification letter after this page)- End of Section -Page 11 of 54 Approved Materials List – Revised November 1, 2011
Page 1 and 2: ENGINEERING SERVICES DEPARTMENTCONS
Page 3: TABLE OF CONTENTSAPPLICABLEITEM PAG
Page 6 and 7: SUBMITTAL GUIDELINES (CONTINUED):7.
Page 8: APPROVED MATERIALS LISTSECTION ONEP
Page 13 and 14: Submittal:DUCTILE IRON FITTINGS (CO
Page 15 and 16: Submittal:VALVE BOXES AND ADAPTERSN
Page 17 and 18: Submittal:VALVE BOXES AND ADAPTERS
Page 19 and 20: Submittal:TAPPING SLEEVES & SADDLES
Page 21 and 22: Submittal:AIR RELEASES:GENERAL:ARV
Page 23 and 24: APPROVED MATERIALS LISTSECTION TWOW
Page 25 and 26: Submittal: 1" WATER SERVICENOTE: Br
Page 27 and 28: Submittal: DUAL WATER SERVICENOTE:
Page 29 and 30: Submittal: EXTENDED & MULTIPLE WATE
Page 31 and 32: Submittal: 3" OR LARGER WATER SERVI
Page 33 and 34: Submittal: 3" OR LARGER WATER SERVI
Page 35 and 36: Submittal: PRIVATE FIRE LINES (CONT
Page 37 and 38: Submittal: PRIVATE FIRE LINES (CONT
Page 39 and 40: Submittal: BACKFLOW PREVENTER(S) (C
Page 41 and 42: APPROVED PRODUCT LISTSECTION THREEG
Page 43 and 44: Submittal: SANITARY GRAVITY SEWER (
Page 45 and 46: APPROVED MATERIALS LISTSECTION FOUR
Page 47 and 48: Submittal: STORMWATER MANAGEMENT ST
Page 49 and 50: Submittal: HARDSCAPE:PEDESTRIAN SUR
Page 51 and 52: APPROVED MATERIALS LISTSECTION EIGH
Page 53 and 54: Submittal: IRRIGATION SYSTEM COMPON

APPROVED MATERIALS LIST (AML) - City of West Palm Beach

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?