ALUCOBOND Verarbeitung - Ravago

More documents

Recommendations

Info

$(Cenik Trespa plo\232\350 2013.xls) - Ravago$

CLEANING AND MAINTENANCE3. Remove the mixture of lacquer and solvent using dry, cellulose wadding.Renew the cellulose wadding, if required.4. Clean the surface again using clean, cellulose wadding moistenedwith small amounts of solvent until any remaining lacquer has beenremoved.5. The ALUCOBOND ® coating then needs to regenerate for at least24 hours, independent of the cleaning result reached. Owing to theabsorption of solvent, the ALUCOBOND ® coating is swollen and inthis state it is sensitive to mechanical stress. The swelling is reversibleand has no influence on the long-term stability of the lacquer coating.6. If there is any remaining paint, steps 2 – 4 should be repeated, but notuntil the lacquered coating has regenerated.General informationAfter cleaning, traces or shaded parts of the former graffiti are possiblystill visible on the ALUCOBOND ® coating. This appearance is caused byorganic dyes that can be in the spray paint and are slightly susceptibleto migration. Therefore, cleaning should take place as soon as possibleto prevent the spray paint from migrating. According to experience,however, these dyes are only slightly lightfast; subsequently, the dyesusceptible to migration is altered and decomposed by solar radiation,thus causing the shading effect to disappear.Large areas of graffiti sometimes lead to producing considerableamounts of cellulose wadding containing residues of solvent and paint.Larger amounts have to be disposed of properly according to WasteCode No. 18702.Attention:--The recommended solvents are inflammable!--Do not smoke under any circumstances near the solvents or during work!--Make sure to allow for good ventilation! Where the exchange of air isrestricted, e.g. pedestrian subways, solvent vapours can accumulate– Danger of explosion!Suitable solvents depending on the lacquer quality*)--Ethanol (methylated spirits) for slight soiling--Hexane (petroleum ether or white spirit)--Methyl glycolic acid--Graffiti Neumann GmbH‚ DEKONTAMINOL*) ALUCOBOND ® has been certified by the laboratories of Dr. Kupfer, Berlin, as havingan anti-graffiti effect that complies with the requirements of the RAL-Gütegemeinschaft(Quality Assurance Association)For further information, e.g. cleaning agents or addresses of approvedcleaning companies, please contact:RAL–Gütegemeinschaft Anti-Graffiti e. V., www.anti-graffiti-verein.de34 Edition 1 ALUCOBOND ® Processing and Technical Data GB
FACADE - STANDARD DESIGNSTray panels suspended on bolts,vertical panel layoutTray panels blue clip with jointsopen to the wind,horizontal panel layoutTray panels SZ 20,horizontal panel layoutRiveted / screwed to verticalsupporting sectionsRiveted to T-sections,closed joints,vertical / horizontal panel layoutEdition 1ALUCOBOND ® Processing and Technical Data GB35
Page 1: PROCESSING AND TECHNICAL DATASimply
Page 4 and 5: TRANSPORTATION, STORAGE1.00 m- 1.20
Page 6 and 7: PANEL INSTALLATIONProtective film w
Page 8: INFORMATION ON SPECIAL SURFACESMill
Page 11 and 12: PROCESSING METHODS--speed 2,400 rpm
Page 13 and 14: PROCESSING METHODSdie for single pu
Page 15 and 16: ROUTING AND FOLDING TECHNIQUEGenera
Page 17 and 18: ROUTING AND FOLDING TECHNIQUEMACHIN
Page 19 and 20: ROUTING AND FOLDING TECHNIQUEFabric
Page 21 and 22: ROUTING AND FOLDING TECHNIQUEFabric
Page 23 and 24: ROUTING AND FOLDING TECHNIQUE(4) Ro
Page 25 and 26: JOINTING / FIXING TECHNIQUE--The to
Page 27 and 28: JOINTING / FIXING TECHNIQUETHREADED
Page 29 and 30: adhesive Sika Tack-Panel orMBE-Pane
Page 31 and 32: JOINTING / FIXING TECHNIQUEFaçade,
Page 33: CLEANING AND MAINTENANCECLEANING AN
Page 37 and 38: TECHNICAL DATA SHEETALUCOBOND ®Thi
Page 39 and 40: TECHNICAL DATA SHEETALUCOBOND ® A2
Page 41 and 42: Internet addressesSealing tapeswww.
Page 43 and 44: Create the differenceVERSATILE ON P
Page 46: Create the difference.3A Composites

ALUCOBOND Verarbeitung - Ravago

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?