Instruction Manual FCX-AII SERIES TRANSMITTERS - Fagerberg

More documents

Recommendations

Info

(2) Shutdown of differential pressure transmitterSet the shutdown status by manipulating the manifold valve.Turn off power supply.Close the stop valve on the high pressure side (H side)slowly.CloseOpenOpen the equalizing valve.CloseClose the stop valve on the low pressure side (L side)slowly.ImportantBefore a long shutdown, discharge the process fluid and drain completely from the transmitter.This is to protect the transmitter from freezing, corrosion, etc.7
4. ADJUSTMENTTo operate the <strong>FCX</strong>-A2 series transmitter, the HHC is used for each adjustment.4.1 Adjustment with HHCStartup and usage of the Hand Held Communicator (HHC) are detailed in the instruction manual forHHC. Please refer to this manual before commencing adjustment.ImportantAfter adjustment of the transmitter, it should be kept energized for about 10 secondsto write the adjustment results into memory.4.1.1 Connection of HHCThe HHC can be connected to the transmitter, junction terminal or the terminals in the instrumentroom.–CK–CK++Field deviceTo HHCTo junctionterminal orinstrumentroomInstrument roomJunction terminalZener barrierTerminal blockLoad resistor250Ω or more Note)DC power supply16.1 to 45V DCNote) See 7.2 “Power voltage and load resistance”.DANGERIn the case of a flameproof transmitter, never connect the HHC to the terminalblock of the transmitter in hazardous area installations.8
Page 1 and 2: Instruction ManualFCX-AII SERIES TR
Page 3 and 4: CAUTION ON SAFETYFirst of all, read
Page 5 and 6: CAUTIONS ON USEBe sure to observe t
Page 7 and 8: 5.3 Replacement of parts ..........
Page 9 and 10: 2. OPERATING PARTS AND THEIR FUNCTI
Page 11 and 12: 3. OPERATION AND SHUTDOWN3.1 Prepar
Page 13: OpenFinally, open the stop valve on
Page 17 and 18: 4.1.3 Operating procedureIn case of
Page 19 and 20: Menu N°3 :SERIAL N°4: UNITINCINC<
Page 21 and 22: Menu N°6 :RANGEDamping adjustment7
Page 23 and 24: Burnout direction9:BURNOUTNOT USED(
Page 25 and 26: Calibration of output circuit (D/A)
Page 27 and 28: [Contents of message]As a result of
Page 29 and 30: 1 2G : XMTR DISPLAY G : XMTR DISPLA
Page 31 and 32: 22BOUT=LIN at Menu No.823G-8 : LOW
Page 33 and 34: INC2H-4:LINEARIZECV1 XXX.XX%< INC>
Page 35 and 36: 4.2 Zero adjustment by the screwZer
Page 37 and 38: 4.4 Local adjustment unit with LCD
Page 39 and 40: 3.2 Span adjustment (Change Upper R
Page 41 and 42: 5.2 TroubleshootingIf an abnormalit
Page 43 and 44: Replacement of detecting unitHexago
Page 45 and 46: In case of absolute pressure and ga
Page 47 and 48: Replacement of field indicator1. Re
Page 49 and 50: 5.4 Adjustment after replacement of
Page 51 and 52: Change of field indicator positionC
Page 53 and 54: Check spaceEnsure a space of about
Page 55 and 56: 0204000%2060204080%401 060%6080801
Page 57 and 58: Cautions on impulse piping• For l
Page 59 and 60: 0204060801 0020400204060608080Typic
Page 61 and 62: Connecting method of the mounting f
Page 63 and 64: 6.2.4 Piping of remote seal type tr
Page 65 and 66:
* The seal liquid density ρ’ is
Page 67 and 68:
Typical examples of piping1 Gas mea
Page 69 and 70:
Terminal block connection diagramTi
Page 71 and 72:
7.3 GroundingCAUTIONThe transmitter
Page 73 and 74:
No. Parts No. Part Name Q'ty Materi
Page 75 and 76:
A1 BUILT-IN ARRESTERGeneralAn arres
Page 77 and 78:
A2 CALIBRATIONPreparation for calib
Page 79 and 80:
Calibration procedure(1) Make wirin
Page 81 and 82:
A4 HAZARDOUS LOCATION INSTALLATION
Page 83:
Fuji Electric France S.A.46, Rue Ge
show all

Instruction Manual FCX-AII SERIES TRANSMITTERS - Fagerberg

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?