IDS 1600 - Adt

More documents

Recommendations

Info

IDS1600 USER MANUALthe entry delay. Although not essential, it is recommended that the [#]key be pressed before entering a user code as this clears anyunintended key entries.Enter the premises through a designated entry/exit door. Enteringvia any other route will cause an alarm.As soon as the entry/exit zone is violated i.e. the door has beenopened, the entry delay begins.The keypad buzzer will sound for the duration of the entry periodto indicate that a valid user code is required.If the ARMED indicator remains illuminated, an error was madewhile entering the user code, press the [#] key and re-enter thecode.Once the system disarms, the ARMED indicator will extinguishand the keypad buzzer will stop sounding.If no valid user code has been entered by the end of the entrydelay period, an alarm condition will be registered.If the entry period is too short, have your installer change theentry delay period.If four incorrect user codes are entered consecutively, the keypadwill be non-responsive for 30 seconds.NOTE:If a strobe (or flashing light) has been installed and an alarm conditionis registered the light will continue flashing after the siren has timedout. Entering a valid [USER CODE] will cancel the strobe.7.2 Disarming a Partition from a Master KeypadHold down [MODE] + [PARTITION NUMBER] + [] + [USER CODE]1. Hold down the [MODE] key on a master keypad until the keypadbuzzer sounds.P A R T I T I O N :ARMTROUBL E2. Enter the [PARTITION NUMBER] you wish to arm followed by the22 IDS1600 USER MANUAL NO. 700-146-01D ISSUED NOV 2002 VER 2.17
IDS1600 USER MANUAL[] key.3. Proceed as if the keypad was assigned to this partition.NOTE:If the ARMED indicator remains illuminated, the wrong user code hasbeen entered. Press the [#] key and re-enter your code. Foursuccessive incorrect codes will result in the keypad locking you out for30 seconds. During this time any code will be treated as incorrect.7.3 To Disarm with a Key-Switch or Remote ControlThis option is not standard; check with your installer to verify if thisfeature is enabled.1. Press the remote button or twist and release the key-switch.2. The system will disarm and the remote indicator (if installed) willextinguish.3. If programmed to do so, the siren will sound briefly - verify withyour installer.8. Emergency Situations8.1 Fire Alarm[F](Hold down the key until the keypad buzzer sounds) If the [F] key is pressed until the keypad beeps (approximately 1second) a FIRE ALARM condition will be activated. The FIRE ALARM CONDITION can also be triggered by a smokedetector connected to an appropriately programmed zone. The siren will sound and the FIRE REPORTING CODE will betransmitted to the monitoring company. To silence the siren enter a 4 digit [USER CODE].IDS1600 USER MANUAL NO. 700-146-01D ISSUED NOV 2002 VER 2.17 23
Page 1: INHEPDIGITALIDSS E C U RI T YUsers
Page 4 and 5: IDS1600 USER MANUAL9.0 Emergency Ev
Page 6 and 7: IDS1600 USER MANUAL1. Introduction
Page 8 and 9: IDS1600 USER MANUAL2.1 Notes on the
Page 10 and 11: IDS1600 USER MANUAL4.2 User CodesUs
Page 12 and 13: IDS1600 USER MANUAL4.3 Zone Informa
Page 14 and 15: IDS1600 USER MANUAL0 1 / 0 1 / 9 9
Page 16 and 17: IDS1600 USER MANUALARMED LED will n
Page 18 and 19: IDS1600 USER MANUAL6. Zone Bypassin
Page 20 and 21: IDS1600 USER MANUALfollowing will b
Page 24 and 25: IDS1600 USER MANUAL8.2 Panic Alarm[
Page 26 and 27: IDS1600 USER MANUAL[#] is pressed.6
Page 28 and 29: IDS1600 USER MANUAL6. Repeat steps
Page 30 and 31: IDS1600 USER MANUAL6. Press [#] to
Page 36 and 37: IDS1600 USER MANUAL14. Chime ZonesT
Page 38: IDS1600 USER MANUAL14.2 To Cancel t
Page 41 and 42: IDS1600 USER MANUAL15.2 View MenuTh
Page 43 and 44: IDS1600 USER MANUAL15.5 Assign User
Page 45 and 46: IDS1600 USER MANUALassigned.Is the
Page 47: IDS1600 USER MANUALMedical ........

IDS 1600 - Adt

Create successful ePaper yourself

Delete template?

Save as template?