BEST 9K Series Service Manual - Locksmith Security Association of ...

More documents

Recommendations

Info

Installation InstructionsA–2 9K Series Service Manual
Installation Instructions for9K Cylindrical LocksFor factory prepared doors only2 Bore two holes and install latchInside roseThrough-boltsInside linerOutside roseLatch1 Bore a 2 1/8" diameter hole from both sides of the door, to the centerof the door.2 Drill a 1" diameter hole from the edge of the door that intersects the21/8" hole.3 Mortise the door edge for the latch face.4 Install the latch and check the door swing. Latch tabs should projectinto the 2 1/8" diameter hole. See figure 3 in step 3.3 Install boring jig and drill two 5/16”diameter holesFigure 1Caution: If you use hollow metal doors, decide whether thedoors are reinforced enough to support the lock. If door reinforcementis not adequate, consult the door manufacturer forinformation on proper reinforcement.Simplified instructions1 Install the latch so that the bevel on the latchbolt faces the strike.2 Adjust the outside rose assembly so that the chassis is centered inthe door. Install the chassis from the outside of the door.3 Install the inside liner, through-bolts, rose, lever and strike.For field door preparation and detailed installation instructions, see thefollowing tasks.1 Position templateHigh edge of door bevelFigure 3Door edge5/16” diameterLatch tabsBoring jig1 Install the boring jig (KD303) onto the door and engage with latchtabs. Make sure the front edge of the jig is parallel with the dooredge (see Figure 3).2 Drill two 5/16" diameter holes halfway into the door.3 Turn the boring jig over and repeat steps one and two from theopposite side of the door.Note: Replace the boring jig after ten door preparations.4 Adjust lockset to door thicknessOne-half door thicknessTEMPLATEHub faceRetractorPull pin to rotate roseHub faceFigure 21 Fold the template and place in position on the high edge of the doorbevel (see Figure 2).2 Mark the drill points.Note: Suggested height from floor to centerline of the lock is40 5/16". If steel frames are used, the latch centerline must be in linewith the center of the strike preparation.■Figure 4Door thickness grooves2 1/4"2"1 3/4"Retract the rose locking pin and rotate the outside rose liner in or outT56075/Rev A 1798029 ER-7991- 19 Mar 2000BEST ACCESS SYSTEMSIndianapolis, Indiana—Continued
Page 2:
CREDITS/COPYRIGHT© 2000-2002 Best
Page 6 and 7:
Contentsvi9K Series Service Manual
Page 9:
FiguresPositioning the lever return
Page 12 and 13:
Getting StartedDOCUMENTATION PACKAG
Page 14 and 15:
Getting Started1-4 9K Series Servic
Page 16 and 17:
Functions and Parts ListsFUNCTION D
Page 18 and 19:
Functions and Parts ListsDouble-key
Page 20 and 21:
Functions and Parts ListsNon-keyedf
Page 22 and 23:
Functions and Parts ListsRZ-Closet
Page 24 and 25:
2-10 9K Series Service ManualSTANDA
Page 26 and 27:
2-12 9K Series Service ManualD FUNC
Page 28 and 29:
2-14 9K Series Service ManualG FUNC
Page 30 and 31:
2-16 9K Series Service ManualL FUNC
Page 32 and 33:
2-18 9K Series Service ManualNX FUN
Page 34 and 35:
2-20 9K Series Service ManualR FUNC
Page 36 and 37:
2-22 9K Series Service ManualT FUNC
Page 38 and 39:
2-24 9K Series Service ManualY FUNC
Page 40 and 41:
2-26 9K Series Service ManualB FUNC
Page 42 and 43:
2-28 9K Series Service ManualDZ FUN
Page 44 and 45: 2-30 9K Series Service ManualIN FUN
Page 46 and 47: 2-32 9K Series Service ManualM FUNC
Page 48 and 49: 2-34 9K Series Service ManualRD FUN
Page 50 and 51: 2-36 9K Series Service ManualXD FUN
Page 52 and 53: 2-38 9K Series Service ManualYD FUN
Page 54 and 55: 2-40 9K Series Service ManualZ FUNC
Page 56 and 57: Functions and Parts ListsStandard f
Page 58 and 59: Functions and Parts ListsTRIM PARTS
Page 60 and 61: Functions and Parts ListsRoses, ros
Page 62 and 63: Functions and Parts Lists13245Figur
Page 64 and 65: Functions and Parts Lists14235Figur
Page 66 and 67: Functions and Parts ListsLatches152
Page 68 and 69: Functions and Parts Lists1234Figure
Page 70 and 71: Service and MaintenanceMAINTENANCE
Page 72 and 73: Service and Maintenance3. Turn the
Page 74 and 75: Service and Maintenance2. Slide the
Page 76 and 77: Service and MaintenanceTo replace t
Page 78 and 79: Service and Maintenance2. Use a pai
Page 82 and 83: Service and Maintenance8. Align the
Page 86 and 87: Service and Maintenance4. Align the
Page 88 and 89: Service and MaintenanceCAM POSITION
Page 90 and 91: Service and MaintenanceEMERGENCY KE
Page 92 and 93: Service and Maintenance3-24 9K Seri
Page 96 and 97: until the proper door thickness gro
Page 98 and 99: For double dummy trim1 Install the
Page 100 and 101: 4 Install the support ring.Support
Page 102 and 103: IndexDZ chassisfunction conversion
Page 104: Indexreinstalling 3-16removing 3-15
show all

BEST 9K Series Service Manual - Locksmith Security Association of ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?