NVIDIA nForce 780i SLI Motherboard - PNY

More documents

Recommendations

Info

780i 3-Way SLI MotherboardConnector Pin Signal Pin Signal12 +3.3V 24 GND8-pin ATX 12V Power (PWR2)PWR2, the 8-pin ATX 12V power connection, is used to provide power to theCPU. Align the pins to the connector and press firmly until seated.Backpanel connector5112VGND8 4Connecting IDE Hard Disk DrivesThe IDE connector supports Ultra ATA 133/100/66 IDE hard disk drives.1. Connect the blue connector (the cable end with a single connector) to themotherboard.2. Connect the black connector (the cable with the two closely spaced blackand gray connectors) to the Ultra ATA master device.3. Connect the gray connector to a slave device.If you install two hard disk drives, you must configure the second drive as aslave device by setting its jumper accordingly. Refer to the hard diskdocumentation for the jumper settings.NVIDIA Corporation14 October 17, 2007 | DU-03597-001_v01
Hardware InstallationNote: If an ATA-66/100 disk drive and a disk drive using any other IDE transferprotocol are attached to the same cable, the maximum transfer rate betweenthe drives may be reduced to that of the slowest drive.NVIDIA CorporationOctober 17, 2007 | DU-03597-001_v01 15
Page 3: Safety Recommendations* Tasks shoul
Page 9 and 10: nForce 780i SLI MotherboardBefore Y
Page 11: NVIDIA nForce 780iMotherboardThank
Page 15: nForce 780i SLI Motherboard2222 252
Page 19 and 20: Hardware Installation7. Close the l
Page 21 and 22: Hardware InstallationSecuring the M
Page 23: Hardware InstallationMake sure you
Page 27 and 28: Hardware InstallationConnecting Int
Page 29 and 30: Hardware InstallationUSB HeadersThi
Page 31 and 32: Hardware InstallationFan Connection
Page 33 and 34: Hardware InstallationFDD ConnectorT
Page 35 and 36: Hardware InstallationJumper Setting
Page 37 and 38: Configuring the BIOSThis section di
Page 39 and 40: Configuring the BIOSPhoenix - Award
Page 41 and 42: Configuring the BIOSStandard CMOS F
Page 43 and 44: Configuring the BIOSPress Enter to
Page 45 and 46: Configuring the BIOSMemoryq All, Bu
Page 47 and 48: Configuring the BIOSRemovable Devic
Page 49 and 50: Configuring the BIOSSecurity Option
Page 51 and 52: Configuring the BIOSSystem ClocksSe
Page 53 and 54: Configuring the BIOSHT Multiplierq
Page 55 and 56: Configuring the BIOS‣ CPUOC 4%‣
Page 57 and 58: Configuring the BIOS‣ ExpertUse t
Page 59 and 60: Configuring the BIOS‣ TM2 OnlyThe
Page 61 and 62: Configuring the BIOSq nForce SPPThi
Page 63 and 64: Configuring the BIOSSave Timing/Vol
Page 65 and 66: Configuring the BIOSIDE Function Se
Page 67 and 68: Configuring the BIOSMAC ConfigPress
Page 69 and 70: Configuring the BIOSACPI FunctionTh
Page 71 and 72: Configuring the BIOSPnP/PCI Configu
Page 73 and 74: Configuring the BIOSIRQ ResourcesTo
Page 75 and 76:
Configuring the BIOSDynamic Fan Con
Page 77 and 78:
Installing Drivers andSoftwareNote:
Page 79 and 80:
Using theNVIDIA SoftwareBuilt upon
Page 81 and 82:
Using NVIDIA SoftwareDevice Setting
Page 83 and 84:
Using NVIDIA SoftwareMotherboardThe
Page 85 and 86:
Using NVIDIA Softwareq Write Recove
Page 87 and 88:
Using NVIDIA SoftwareGPUThe graphic
Page 89 and 90:
Using NVIDIA SoftwareView System In
Page 91 and 92:
Using NVIDIA SoftwareManage Your Sy
Page 93 and 94:
Using NVIDIA SoftwareIn this exampl
Page 95 and 96:
Using NVIDIA SoftwareThe second ser
Page 97 and 98:
Appendix A.POST Codes for Tritium P
Page 99 and 100:
Post CodesAward POST CodesCodeNameD
Page 101 and 102:
Post CodesAward POST CodesCodeNameD
Page 103 and 104:
Post CodesAward POST CodesCode8ENam
Page 105 and 106:
Post CodesNVMM POST CodesCode Name
Page 107 and 108:
Appendix B.Configuring an SLI Confi
Page 109 and 110:
Configuring 3-Way SLIThree GPUs are
Page 111 and 112:
Configuring 3-Way SLIBefore closing
Page 113 and 114:
Index1394 Cable, 42-Port SATA Power
Page 115 and 116:
Configuring 3-Way SLIGlobal Setting
Page 117 and 118:
Configuring 3-Way SLIPOST CodesAwar
Page 119 and 120:
NoticeALL NVIDIA DESIGN SPECIFICATI
show all

NVIDIA nForce 780i SLI Motherboard - PNY

Create successful ePaper yourself

Delete template?

Save as template?