Nova DVR 3000 Manual_22 November 2002 - Teknatool

More documents

Recommendations

Info

Mounting the Lathe to a Support SurfaceBolt tightening sequence2nd1st3rdMaximum of 25 mm (1 in.)(Required only for mounting theOutrigger Unit option.)!Mounting Holes (6)The lathe must be fastened to asupport surface, such as a lathestand or bench.1. Place the lathe on the stand top. Locate the front and left corner of the latheapproximately 25 mm (1 in.) from the corner edge of the stand top. This provides acomfortable reach when turning and allows the optional outrigger unit to be easily installed.2. If necessary, mark the six hole locations on the top and drill M12 (1/2-inch) holes.3. Place a spirit level along the top of the lathe bed. Any movement of the bubble as thelathe is secured, indicates a twist on the bed. For the lathe to operate correctly the bedmust not twist; if necessary, use shims between the bed and stand top.4. Use bolts of suitable length (not included) to secure the lathe. Tighten the two headstockbolts first, then the two tailstock bolts, and finally tighten the two middle bolts.5. The two 12mm threaded holes underneath the outrigger end of headstock can be optionallyused (making a total of 8 bolt positions) ensure that the bolt is a metric M12 x 1.75 mmpitch and that the length is correct to ensure that the bolt doesn't bottom in the threadedhole and potentially damage casting.Connecting to PowerThe power cord should be 3-wire, having a grounding conductor and a grounding plug. The plugmust be plugged into a matching outlet that is properly installed and grounded in accordancewith local electrical codes.! Warning!Improper connection of the motor can result in a risk of electricalshock.If it is necessary to use an extension cord, the cord should be grounded. Use the proper wiresize for the extension cord, for a given cord length, to avoid power loss and over-heating.55016 115v 15 amp wall connection.55078 220-240v x 10 amp or 15 amp wall socket connection.14 101-0505-002
Using the Nova DVR 3000Parts of the Nova DVR 3000 WoodlatheTailstockIndexHeadstockQuilHandwheeSpindleQuil 2MTHandbrakToolslidToolrestTailstockClamp HandleHeadstockLockpinDVR Controller &Switch coverBedToolslide ClampHeadstock LockpinOperating barDVR Variable Speed Controllercontrol.The DVR 3000 drive is a unique type of motor and controller, the motor andcontroller interact, the motor provides data to the controller on its position andload conditionsThe motor provides high torque even at low rpm and extremely close speedWith the on /off switch down plug lead into wall socket and switch on.Some music will be heard as the controller computer" boots up " and the LCD display will showa two line display.DVR Drive ParametersMotor Type: Digital Variable Reluctance Accuracy of Speed Stabilization: 0.80Motor Speed Range: 250-3500 rpmDefault speed (when powering up) : 600 RPMRegulator Type: PIDSpeed Stabilization: Current level, pulse widthReverse: YesRamp Facility: By speed, by torqueSpeed Control: Button (10rpm increment)101-0505-002 15
Page 1 and 2: NOVADVR 3000 TMWOODLATHEINSTRUCTION
Page 3 and 4: 101-0505-002 3
Page 5 and 6: Contact Teknatool?Teknatool Interna
Page 7 and 8: GENERAL SAFETY RULES! Warning! Fail
Page 9 and 10: DVR 3000 Woodlathe SpecificationsSi
Page 11 and 12: Example of Shop-made Lathe StandTop
Page 13: 5. Assemble the handles:? Note: Som
Page 17 and 18: 6. FWD / REV keys. Pressing this ke
Page 19 and 20: HeadstockThe headstock houses the m
Page 21 and 22: Lathe Turning speedsCorrect selecti
Page 24 and 25: Cleaning the TailstockIf the tailst
Page 26 and 27: Troubleshooting Guide continuedProb
Page 28 and 29: 40 1 55019 Interface board41 1 5504
Page 30 and 31: 101-0505-002 30
Page 32 and 33: AccessoriesFaceplates:FP150Z with I
Page 34 and 35: Teknatool WarrantyTeknatool Five Ye
Page 36 and 37: Steps to registering your Warranty

Nova DVR 3000 Manual_22 November 2002 - Teknatool

Create successful ePaper yourself

Delete template?

Save as template?