Regloplas- Temperature Control Technology

More documents

Recommendations

Info

RT100 and RT61 controlsystems, controller RT32The RT100 control system ensures an optimal fit forpractically every application. The RT61 control system andthe RT32 controller are simple, cost-effective solutions fora wide variety of applications.All controllers are designed to avoid problems beforethey arise.Modern automatedmanufacturing processesrequire data trans -fer between the temperaturecontrol unitand the productionfacility’s central computer– just one ofmany applications forthe RT100 and RT61control systems withdata interface.16
Equipment RT100 RT61 RT32Operation and control3.5" colour TFT display • – –Selectable language, incl. Chinese • – –Operate with a sturdy rotary knob RCD (Regloplas Control Dial) • – –Symbol field for displaying active functions and directions • – –Dual units can be operated only via one display • – –Logbook for alarms • – –USB interface (host/device) • – –Ramp program ᐤ – –Flow-rate deviation monitor ᐤ – –Temperature limit values (+/–) adjustable • • ᐤControl of the consumer temperature with cascade control for highest temperatureconstancy with 2 control circuits (consumer and fluid)ᐤ – –Set-point switch-over (value 1/value 2) • – –External sensor connection for Pt100, J (Fe-CuNi), K (NiCr-Ni) or T (Cu-CuNi) ᐤ – –Leak-stop operation ᐤ/– •/– •/ᐤ/–Drainage of the fluid from the consumer by suction/blow out ᐤ/– •/ᐤ •/ᐤ/–Time switch ᐤ – –Flow rate measurement from 2 to 200 l/min for water and oil up to 350 °C ᐤ ᐤ ᐤContactless flow-rate measurement F1000 ᐤ – –Inlet sensor (Pt100) ᐤ – –External control: set-point switchover, heating/cooling command ᐤ – –External control: set-point input, switching the unit on/off ᐤ ᐤ –Data interfaces ᐤ ᐤ –Scalable recorder outputs ᐤ ᐤ –Heater-current monitor ᐤ – –SafetyAll disturbances in the unit are indicated on the display • • –Set-point ‘blockable’ as protection against incorrect adjustment • – –Monitoring of upper and lower limit values • • ᐤUnauthorized access to the programming levels prevented by a code • • –Automatic pump rotation correction • • –Sensor-failure monitoring • • •Automatic switch-over to the internal sensor (fluid) in the eventof external sensor failureᐤ – –Units with automatic water refilling: In order to limit the consequences of leakage (i.e.hose burst) the filling time per refill and the number of refills per hour is limited in order toprotect the production installation against damage caused by water• • –Common acoustic alarm • • •Visual alarm, colour LEDs • – –ServiceIndication of the service interval • • –Operating hours meter • • –Programmed data remains stored during replacement of electronic components • – –RT100RT61RT32• Standard equipment ᐤ Option – Not available •/–; ᐤ/– Unit-specific Further options available upon request17
Page 1: MASTER OF TEMPERATURE CONTROLReglop
Page 5: Standard equipmentElectrical sectio
Page 8 and 9: Pressurised-watertemperature contro
Page 10: Technical data P100S P100M P140smar
Page 13 and 14: Standard equipmentElectrical sectio
Page 15: Pump capacity. Flow rate Vas a func
Page 19 and 20: Models with air-cooled condenser an
Page 21 and 22: REG Descaling unit• Incorporated
Page 23 and 24: InterpretingRegloplas dataNotesThe
Page 25 and 26: FittingsDimensions in mm if not spe
Page 27 and 28: 4. Twin connector with ball cocks f
Page 29 and 30: Temperature sensorsAccessoriesExamp
Page 31 and 32: Since there is very little systemat

Regloplas- Temperature Control Technology

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?