Regloplas- Temperature Control Technology

More documents

Recommendations

Info

Pressurised-watertemperature controlunits up to 180°CTemperature control of plastic injection moulds,diecasting dies, rollers, extruders, mixers and otherapplications.Superior heat transfer has a direct effect upon theoutput of your production plant.Pressurised water units canbe implemented wherever thereare advantages of water as aheat transfer fluid.Patented low-scale coolingsystem ‘SK’.8
Standard equipmentElectrical section• RT100 or RT61 control system ➔ Optimal fitfor practically every application.• Electric control in accordance with IECstandards. Tropic-proof up to 90% humidity.Completely separated from the pumpingsection and protected against direct contact➔ Safe operation.Mechanical section• Operating temperature independent ofcooling water pressure ➔ Flexible operation.• All components exposed to water are madeof non-ferrous materials. Tank made of stainlesssteel ➔ Long service life.• Heating elements made of heat-resistantalloy Incoloy® for high corrosion resistance➔ Safe operation, long service life.• Sturdy and powerful centrifugal pump highcapacity ➔ Quick compensation of disturbances,good regulating performance.• Filter in cooling water inlet.• Low-scale, dual-circuit cooling system‘SK/2SK’ ➔ Significant reduction of scaling inthe cooler (not available for the P140smart).• Automatic water refill.• Leak-free Pump (except SG85).Safety• Safety valve ➔ Prevents excessivepressure in the unit.• Pressure gauge for system pressure.• Safety thermostat ➔ Protection againstoverheating.• Automatic fluid level control➔ Protection against running dry.• Acoustic common alarm.P100SP100MP140smartP160SP160M(D)P161XLP180SP180M(D)Quality assurance: At Regloplas, all units, whether standard orcustomised, undergo all phases of rigorous final testing.Unit-specific equipmentEquipment P100S P100M P140smart P160S P160M(D) P161XL P180S P180M(D)Control system RT100 (options see page 17) • • – • • • • •Control system RT61 (options see page 17) – – • – – – – –Solid-state Relay (SSR) instead of heating contactor • • • • • • • •Electronic flow measurement ᐤ ᐤ ᐤ ᐤ ᐤ ᐤ ᐤ ᐤManual shut-off valve in the inlet and outlet ᐤ ᐤ – ᐤ ᐤ • ᐤ ᐤInlet filter • • ᐤ • • • • •Display of outlet pressure on RT100 ᐤ ᐤ – • • • • •Drainage of the fluid from the consumer by suction ᐤ ᐤ ᐤ • • – • •Patented low-scale cooling system «SK» – – – • • • • •Unit in IP54 protection degree • • – • • • • •• Standard equipment°Option – Not available Further options available upon request9
Page 1: MASTER OF TEMPERATURE CONTROLReglop
Page 5: Standard equipmentElectrical sectio
Page 10: Technical data P100S P100M P140smar
Page 13 and 14: Standard equipmentElectrical sectio
Page 15 and 16: Pump capacity. Flow rate Vas a func
Page 17 and 18: Equipment RT100 RT61 RT32Operation
Page 19 and 20: Models with air-cooled condenser an
Page 21 and 22: REG Descaling unit• Incorporated
Page 23 and 24: InterpretingRegloplas dataNotesThe
Page 25 and 26: FittingsDimensions in mm if not spe
Page 27 and 28: 4. Twin connector with ball cocks f
Page 29 and 30: Temperature sensorsAccessoriesExamp
Page 31 and 32: Since there is very little systemat

Regloplas- Temperature Control Technology

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?