2P/2P 6~10KVA Online UPS User Manual - Voltron

More documents

Recommendations

Info

• 10: Bypass mode settingInterfaceSettingParameter 2:OPN: Bypass allowed. When selected, UPS will run at Bypassmode depending on bypass enabled/disabled setting.FBD: Bypass not allowed. When selected, it’s not allowed forrunning in Bypass mode under any situations.Parameter 3:ENA: Bypass enabled. When selected, Bypass mode is activated.DIS: Bypass disabled. When selected, automatic bypass isacceptable, but manual bypass is not allowed. Manual bypassmeans users manually operate UPS for Bypass mode. Forexample, pressing OFF button in AC mode to turn into Bypassmode.• 11: Battery maximum discharge time settingInterfaceSettingParameter 3:000~999: Set the maximum discharge time from 0min to999min. UPS will shut down to protect battery when batteryvoltage is low. The default value is 990min.DIS: Disable battery discharge protection and backup time willdepend on battery capacity.• 12: Neutral loss detectionInterfaceSettingParameter 2:N.L: Indicates neutral loss detection function.Parameter 3:DIS: Disable the neutral loss detection function. The UPS will notdetect the neutral loss or not.ATO: The UPS will automatically detect the neutral is lost or not. Ifneutral loss is detected, an alarm will be generated. If the UPS isturned on, it will transfer to battery mode. When neutral isrestored and detected, the alarm will be muted automatically andthe UPS will go back to normal mode automatically.ATO is default setting.CHE: The UPS will automatically detect the neutral loss. If neutralloss is detected, an alarm will be generated. If the UPS is turnedon, it will transfer to battery mode. When neutral is restored, thealarm will NOT be muted automatically and the UPS will NOT goback to normal mode automatically.Here, you must mute the alarm and make the UPS go back tonormal mode manually. The operation is: Firstly, enter this menuand press the “Enter” key to make the “CHE” flash. Secondly, pressthe “Enter” key again to activate the neutral detection (check). Ifneutral is detected, the alarm will be muted and the UPS will goback to normal mode. If neutral is not detected, the UPS willcontinue alarming and stay on the latest status until the neutral isdetected well at next manual checking operation.17
• 13: Battery voltage calibrationInterfaceSettingParameter 2: Select “Add” or “Sub” function to adjust batteryvoltage to real figure.Parameter 3: the voltage range is from 0V to 9.9V, the defaultvalue is 0V.• 14: Charger voltage adjustmentInterfaceSettingParameter 2: you may choose Add or Sub to adjust chargervoltageParameter 3: the voltage range is from 0V to 9.9V, the defaultvalue is 0V.NOTE:*Before making voltage adjustment, be sure to disconnect allbatteries first to get the accurate charger voltage.* Any modification should be suitable to battery specifications.• 15: Inverter1 voltage adjustmentInterfaceSettingParameter 2: you may choose Add or Sub to adjust inverter1voltageParameter 3: the voltage range is from 0V to 9.9V, the defaultvalue is 0V.• 16: Inverter2 voltage adjustmentInterfaceSettingParameter 2: you may choose Add or Sub to adjust inverter2voltageParameter 3: the voltage range is from 0V to 9.9V, the defaultvalue is 0V.18
Page 2 and 3: Please comply with all warnings and
Page 4 and 5: 1. Safety and EMC instructionsPleas
Page 7 and 8: Diagram 3 : 10K Input/Output Termin
Page 9 and 10: NOTE 2: Please install the output b
Page 11 and 12: LCD Panel:DisplayBackup time inform
Page 13 and 14: for system safety.5) If the overloa
Page 15 and 16: 3-5. Abbreviation Meaning in LCD Di
Page 17 and 18: • 01: Output voltageInterface•
Page 19: • 05: Voltage range for bypassInt
Page 23 and 24: AC mode Description When the input
Page 25 and 26: LCD displayWarningstatusDescription
Page 27 and 28: 4. Trouble ShootingIf the UPS syste
Page 29 and 30: 5. Storage and Maintenance5-1. Stor

2P/2P 6~10KVA Online UPS User Manual - Voltron

Create successful ePaper yourself

Delete template?

Save as template?