MULTI S400 - Seatronic

More documents

Recommendations

Info

2.4.9. Resetting data in the memoryAt any time, the memory of the Multi display can be returned to factory settings. Todo so, a memory reset command is accessible in the menu. The followingparameters are restored in the memory: Speed unit: Knots Depth unit: Metres Distance unit: Nautical Miles Temperature unit: °Celsius Speed damping: 10 seconds Speed calibration coeff.: Slope at 1.0 Temp. calibration coeff.: Offset to 0 Keel offset: 0 Depth alarms: deactivated, high and low threshold at0 Speed alarms: deactivated, high and low threshold at0 Temperature alarms: deactivated, high and low threshold at0 Battery alarm: deactivated, low threshold at 0 Countdown timer init.: 10 minutes Trip log: 0 Total log: 0 Simulation mode: deactivated Backlighting level: 0 (OFF)Press menu for 2 seconds, then menu until the "rESEt" page isdisplayed, then activate (on) or deactivate (OFF) the reset usingthe and keys.Pressto exit setup mode, or time out after 10 seconds.2.5. StandbyTo save energy on board, the "MULTI" display can be placed on standby by pressingfor 5 seconds on the key.Standby mode switches off backlighting, the screen, stops sensor measurement andprocessing of NMEA input and output interfaces. Only the vital bus management andkeyboard functions remain active. Active displays present on the bus indicatemeasurement impossible with an OFF icon instead of the data.Installation and Operation Manual S400 series 15
Standby mode is not saved. At any time, simply pressing one of the four keysor cutting off the power stops standby mode and returns all devicefunctions to normal.2. 6. Network operation (Bus AS-1)The AS-1 bus is used to connect products in the advanSea family via a rapid andreliable exchange protocol. Only the bus wires need to be connected. No start-upsettings are required.The communication protocol allows for multiple data exchange at previously definedtransmission speeds.Thus, it is possible: to exchange several similar measurements on the same bus, forexample: several speedometer sources. to change the units, the alarm threshold values or to calibrate from asingle instrument. to activate or deactivate alarms from a single instrument.The protocol allows exchange of similar data from different sources (directmeasurement from the sensor, or from the bus or via NMEA).2.6.1. Displaying multiple dataIn order to display multiple data, a repeater instrument (without a sensor) should bedifferentiated from a measurement instrument (with a sensor or receiving NMEAdata).A repeater instrument can display maximum 2 multiple data available on the bus(for example: port speed and starboard speed). If there are more than 2 multipledata present on the bus (for example 3 speed sensors), the repeater will only readthe information from the 2 measurement instruments with the lowest serialnumbers.A measurement instrument (with a sensor or receiving NMEA data) will only displaythe data from its own sensor or from the NMEA source received, even if othersimilar data are available on the bus.2.6.2. Remote accessA repeater instrument (without a sensor) can read and write, via AS-1 bus, all thecalibration parameters or the alarm thresholds from the same type of measuringinstrument. Thus, it is possible to calibrate the speed from the MULTI displayconnected to the bus.Installation and Operation Manual S400 series 16
Page 2 and 3: WarningS400 advanSea instruments co
Page 4 and 5: 3. Installation3.1. NMEA 0183 inter
Page 6 and 7: To do so, it is supplied with 3 con
Page 8 and 9: 2 General operation2.1. Powering on
Page 10 and 11: 2.2.3. Selecting units of measureme
Page 12 and 13: An alarm can be cancelled and inhib
Page 14 and 15: 2.4.3. Calibrating the water temper
Page 18 and 19: System limitation:For complex insta
Page 20 and 21: 3.2. Mounting and connections3.2.1.
Page 22 and 23: Alimentation 12V power supply 12 vo
Page 24 and 25: FRANCE & SWITZERLANDPlastimo France

MULTI S400 - Seatronic

Create successful ePaper yourself

Delete template?

Save as template?