IG4300 Owner's Manual NTP Edit 2 - Kipor Power Systems

More documents

Recommendations

Info

$H:\drawings\IG3000\KG205GETi(EPA)(CARB)å¾å.dwg Model (1)$

6. STOPPING THE ENGINE6.1 Normal Shutdown1. Switch off the connected equipment and disconnect from the generator.2. Turn off the engine switch.3. Turn the fuel valve lever to the OFF position.6.2 Emergency StopTurn the start switch to the OFF position.Continually stopping the generator with a load applied can lead todamage of the control module.22
7. MAINTENANCEThe purpose of the maintenance and adjustment schedule is to keep the generator in the bestoperating condition.Shut off the engine before performing any maintenance. If the enginemust be run, make sure the area is well ventilated. The exhaustcontains poisonous carbon monoxide gas.Use genuine <strong>Kipor</strong> parts or the equivalent. The use of replacementparts which are not of equivalent quality may damage the generator.7.1 Emission Control SystemEmission sourceExhaust gas contains carbon monoxide, nitrous oxide (NOx), and hydrocarbons. It is very important tocontrol the emissions of NO X and hydrocarbons as they are a major contributor to air pollution. Carbonmonoxide is a poisonous gas. The emission of fuel vapors is a source of pollution as well. The <strong>Kipor</strong>generator engine utilizes a precise air-fuel ratio and emission control system to reduce the emissionsof carbon monoxide, NO X , hydrocarbons, and evaporative fuel emissions.RegulationYour engine has been designed to meet current Environmental Protection Agency (EPA) and theCalifornia Air Resources Board (CARB) clean air standards. The regulations dictate that themanufacturer provide operation and maintenance standards regarding the emission control system.Tune up specifications are provided in the Specifications section and a description of the emissioncontrol system may be found in the appendix to this manual, Adherence to the following instructionswill ensure your engine meets the emission control standards.ModificationModification of the emission control system may lead to increased emissions. Modification is definedas the following: Disassembling or modifying the function or parts of the intake, fuel or exhaust system. Modifying or destroying the speed governing function of the generator.23
Page 1 and 2: SINEMASTERDIGITAL GENERATORIG4300OW
Page 3: Thank you for purchasing a Kipor Ge
Page 6 and 7: 8. TRANSPORTING/STORAGE ·····
Page 8 and 9: To ensure safe operation: Gasoline
Page 12 and 13: 3. PRE-OPERATION CHECKBe sure to ch
Page 14 and 15: Gasoline containing alternate fuels
Page 16 and 17: 4.1(b) Pull the choke knob out to t
Page 18 and 19: 4.2 High altitude operationAt high
Page 20 and 21: When an extension cable is required
Page 22: Be sure that all appliances are in
Page 25 and 26: The battery contains sulfuric acid
Page 27: With the voltage switch in the 120/
Page 31 and 32: 7.2 Maintenance Schedule(1) REGULAR
Page 33 and 34: Air Filter BaseFilter Element Air F
Page 35 and 36: 1. Remove the generator rear cover
Page 37 and 38: 9. TROUBLESHOOTINGWhen the engine w
Page 39 and 40: 10. SPECIFICATIONSModelIG4300TypeIn
Page 41 and 42: 12. WHEEL KIT1. Axle shaft2. 2.5’
Page 43 and 44: 13. WARRANTY13.1 Kipor Power Equipm
Page 45: C. Gaskets5. Crankcase Breather Sys
Page 48 and 49: Fuel System42
Page 50: Exhaust System44

IG4300 Owner's Manual NTP Edit 2 - Kipor Power Systems

Create successful ePaper yourself

Delete template?

Save as template?