Operation Manual for NDJ Series and SNB Series ... - Mrclab.com

More documents

Recommendations

Info

of the selected rotor is displayed on the screenThe selection of SNB Series Product: Once pressing the key for the speed, 60 or 60.0will be displayed on the screen and flickering “6”.At this time, you can press the key fornumber going up or going down to set the tens digit of the rotating speed. And then press thekey shifting rightwards to set the tens digit of the shifted number or decimal point. If the shiftis needed in reverse direction, press the key shifting leftwards. In this way, you can set thevalue of other digit. Press the key for confirmation when the setting is over.(7) By revolving the knob of the ascending and failing rack, the viscosity meter will godown slowly and the rotor will immerge into the liquid that will be measured until the markof the rotor is in the same level with the liquid. And then adjust the position of the viscositymeter to the level.(8) By pressing the key for measurement, you can measure the viscous value of therotor under the current rotating speed and mark of the percentage meter at the same time.(9) In the course of measurement, if you need to change the rotor, you can press thekey for rotor directly. At this moment, the motor stops and the viscosity meter is still powered.After the rotor is changed, you can continue to measure as per the procedures (6)and (8)above mentioned.(10) Printinga. Firstly, you should select the time interval for printing. After press the keyfor printing, S:00:05 will be displayed on the screen. The time interval for printing will bechanged once you press the key for printing. 00:05→00:10→00:20→00:30→01:00→01:30→02:00→05:00→ will be displayed on the screen to and fro.S:00:05 stands for printing every 5 seconds, 00:10 stands for printing every 10seconds, ……05:00 stands for printing every 5 seconds. The rest result can be known bythis way.When the time interval for printing on the screen is desired, the selection of the timeinterval for printing is over. For SNB Series Product, you should press the key for printingagain for final confirmation.b. After connected with the printer, you should press the key for printing once again.“on” printed on the printing paper stands for the time interval desired. After pressing the keyfor printing, “off” printed on the printing paper stands for the end for printing8. Sampling measurement for unknown viscosity(1) The General Principle for Measurement: For the sample with high viscosity, youshould choose the little dimensioned rotor ( No.3, No.4) and slow rotating speed. For thesample with low viscosity, you should choose the large dimensioned rotor ( No.1,No.2) andfast rotating speed. When measured ,the mark measured by the percentage meter between20% and 90% is the normal value. The viscous value measured within this range is thecorrect value.(2)You should estimate the viscous range of the sample to be measured first and thenchoose the little dimensioned rotor and the slow rotating speed as per the sample with highviscosity and choose the large dimensioned rotor as per the sample with low viscosity. Inmost cases, you should choose the rotor and then choose the approximate rotating speed. Forexample, when the rotor SP is No.1,the rotating speed 60RPM,the full capacity displayed onthe screen is100mPa.s. And when the rotating speed is changed into 6RPM,the full capacity is6
1000mPa.s。(3) When you can not estimate the viscosity of the sample to be measured, you shoulddecide on the rationality of the rotor and the rotating speed as per the mark of the percentagemeter (wresting square).The mark of the percentage meter between 20%—90% is thenormal value. If the value is not beyond this limit, the viscosity meter will alarm, remindingthe user to change the rotating speed and rotor. Never forget to change the rotor as per theprinciple that the rotor is changed with changing the number of the rotor SP.9. Cautions(1) Be careful in installing and uninstalling the rotor. When installed and uninstalled,you should operate by uplifting the joint bolt slightly. Do not do it more forcibly. Do notmake the rotor receiving the force horizontally to prevent the rotor from being bended.(2) Do not put the viscosity meter that is already installed aside or lay it down;(3)Keep the connecting side of the joint bolt with the rotor and the screw thread itselfclean. Otherwise, it will effect the shacking degree of the rotor;(4) You should hold the ascending and failing rack in your hand when it is on raise anddown to prevent it from dropping due to its deadweight;(5)After changing the rotor, you should input the new number of the rotor. The rotor thatis used and changed should be cleaned first and then put on the rack of the rotor. Do not leavethe rotor on the meter and clean it.(6)When the liquid is changed, you should clean (wipe up) the rotor and the protectiveframe of the rotor to avoid the error caused by the interblended liquid for measurement.(7)The viscosity meter is matched with the rotor. Do not interblend several viscositymeters with the rotors(8)Do not dismantle and adjust the spare parts in the viscosity meter with liberty.(9)When the viscosity meter is moved and transported, the yellow cap should be on thejoint screw and the bolt should be screwed down and packed in the box.(10)After the rotor is installed, you do not circumrotate it for a longer in case of no liquidto prevent it from being damaged.(11)The suspended and confused liquid, high polymer and the other more condensedliquid have a lot of “ non Newton liquid”. Their viscous values are varied with the shearspeed and the time. Therefore, their checking results under the different rotors and rotatingspeed are different. This is the normal case. It is not the error caused by the meter. Normally,you should regulate the rotor ,rotating speed and time to measure the non Newton liquid.(12)The following points you should pay more attention for more accurate dataa. More precisely control the temperature of the liquid to be measuredb. Putting the rotor into the liquid to be measured for an enough longer time and keepthe same temperature for bothc. Keep the uniformity of the liquidd. When measured, the rotor is placed in the center of the vessel and the rotorprotective frame must be installed;e. To make sure the cleanliness and shacking degreef. You should turn off the apparatus at time when the measurement at high speed ischanged into the measurement at low speed at one or keep a less longer time at thelow speed to overcome the error that may be caused by the circumvolved inertia of7
Page 1 and 2: NDJ Series Product Standard: Q/SGKW
Page 3 and 4: 1. Main Technical ParametersModel N
Page 5: RotorRotor Selection. The viscous v
Page 9: Operation Manual for NDJ Series and

Operation Manual for NDJ Series and SNB Series ... - Mrclab.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?