Atari Airborne Avenger Manual - Mame channel

More documents

Recommendations

Info

Figure 6: Location of Playfield Switches and SolenoidsNOTE: Toggle 1 of PROG SW1 on Processor PCB should always remain in off position. For bench test purposes, Self-Test mode may beactivated by setting PROG SW1 toggle 1 to on then off. This simulates pressing the TEST pushbutton.
SUGGESTION: Perform Self-Test no less than each time the cash box is collected. Machines in good operating condition have been provento earn more money.SUGGESTION: While performing Self-Test, inspect the playfield for worn rubbers or dirt. Clean the playfield glass and outside of thecabinet regularly. Clean games attract more players and therefore earn more moneyF. VOLUME ADJUSTMENTThe volume control for all game sounds is located inside the cabinet above and to the right of the game speaker To adjust the volume, turn thevolume control clockwise to increase the volume and counter-clockwise to decrease the volume.A second volume control is located inside the cabinet on the Auxiliary PCB (labeled VOL). This volume control should only be adjusted by aqualified technician. Technicians may learn the proper adjustment of this control by reading the instructions in the Maintenance chapter(Chapter 3) of this manual.Table 1: Self-Test ProcedureTest Name Test Instruction Indication of of Test Mode Test Results Operator ActionLamp Test Press and release (once only)the TEST pushbutton. (The(Test number) 1 appears in4TH UP player scoreAll lamps are lighted (ignoreback boxlamps).Check to ensure that alllamps are lighted.TEST pushbutton is located on display.High replay level is displayed inthe inside top middle of the1ST UP player score display.coin door.)Switch TestPress and release (once only)TEST pushbutton.Solenoid Test Press and release (once only)TEST pushbutton.(Test number) 2 appears in4TH UP player scoredisplay.(Test number) 3 appears in4TH UP player scoredisplay.Medium replay level isdisplayed in 2ND UP scoredisplay.Low replay level is displayed in3RD UP player score display.Number of balls per game isdisplayed in BALL display.Maximum credits is displayedin CREDIT display.Any activated or stuck switchesare identified by a number inthe CREDIT display. A pulsingtone is heard when a switch isactivated or stuck.Each solenoid is individuallyenergized and identified by anumber in the CREDIT display.To change, adjust ReplayRotary switch and PROGSW1 toggle 4 for the resultsas listed in Table 2.To change, set DIP switchPROG SW 2 toggle 1 to ONfor 3 balls, OFF for 5 balls.To change, set DIP switchPROG SW 1 toggles 5 and 6as listed in Table 3.NOTE: To exit Self-Test,press and release the TESTpushbutton three times.Identify activated or stuckswitches as listed in Table 4.NOTE: To exit Self-Test,press and release the TESTpushbutton two times.Press left flipper button toactivate solenoid. Press rightflipper button to change tonext solenoid. Identify eachsolenoid with number inCREDIT display as listed inTable 5.NOTE: To exit Self-Test,press and release the TESTpushbutton one time.RotarySwitchSettingPROG SW1Toggle 4Table 2 Replay Level SettingsLow ReplayLevelMedium ReplayLevelHigh ReplayLevel0 OFF 50,000 70,000 90,000
Page 2 and 3: ATARI INC1265 BORREGAS AVENUEP.O. B
Page 4 and 5: Location of Serial NumbersWARRANTYS
Page 7 and 8: 1.2.3.4.5.6.7.Solenoid Driver Circu
Page 9 and 10: ●●●●●●●●●Table 7:
Page 11 and 12: Figure 1: Inventory of AccessoriesW
Page 13 and 14: 2. Attach Back BoxCAUTION: Back Box
Page 15 and 16: Figure 4: Final Assembly and Inspec
Page 20 and 21: 1 OFF 60,000 90,000 120,0002 OFF 70
Page 22 and 23: *1 coin, 1 credit *1 coin, 1 credit
Page 24 and 25: Up to the table of contentsBack to
Page 26 and 27: coin mechanisms will not accept any
Page 28 and 29: Up to the table of contentsBack to
Page 30 and 31: F2 Logic 7 amps, 250 volts, slo-blo
Page 32 and 33: Figure 10: Removal of Coin Mechanis
Page 34 and 35: Adjustment of Coin Switch Trip Wire
Page 36 and 37: Figure 14: Coin Mechanism, Exploded
Page 38 and 39: On Match/Credit Display PCB, place
Page 40 and 41: Figure 19: Line-up of Terminal Pins
Page 42 and 43: Figure 21: Location of Technician A
Page 44 and 45: By means of a switch sensing circui
Page 46 and 47: Figure 25-A: Processor PCB Schemati
Page 48 and 49: 606162 79-42040 1 Socket, 40 Positi
Page 50 and 51: 28 37-7407 4 I.C. 7407 D14, D16,D18
Page 52 and 53: 42 37-9316 2 I.C. 9316 B4, D1343 37
Page 54 and 55: 15 19-311502 1 Trimpot, 5000 ohms R
Page 56 and 57: Address Bus. Keep in mind that thes
Page 58 and 59: Figure 31: Additional Components to
Page 60 and 61: Figure 33: Simplified Diagram of Sw
Page 62 and 63: Figure 35: Waveforms for Gas Discha
Page 64 and 65: Figure 29-B: Match/Credit PCB Assem
Page 66 and 67: For the circuit descriptions that f

Atari Airborne Avenger Manual - Mame channel

Create successful ePaper yourself

Delete template?

Save as template?