v.S1 Cylindrical Lock Installation Instructions 1.10 - Access Control ...

More documents

Recommendations

Info

Profile Series v.S1 PoE Cylindrical Lock6 Installation WiringA PoE frame harness assembly (From McKinney)B PoE data hinge (Patent Pending) (From McKinney)C PoE door harness* (From McKinney)DEDPS: Door Position Switch (cylindrical and exits only)Profile Series v.S1 PoE lock* Order of installation may vary.Refer to appropriate sections for instructions.Supplied by CIB-SpliceCrimp ConnectorCertified Integrator (CI) supplies and terminatesthe B-Splice connector and theMale RJ45 connector from harness toend user provided facility cableDrain WirePatch Cable:Patch Panel toPoE SwitchSupplied by End UserPoE SwitchPoE Switch isterminated toEarth groundCeilingRJ45-MRJ45-F JackCable: CAT 5e or higher24 AWG shielded with drain wirePatch PanelDrain Wire Terminated on RackCopyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.24AWGStrandedWire forEarthGroundinside15' FrameHarnessFrame-SideHarnessAssembly(15' length)Cabledrain wireconcealedin shrinktubingCable: CAT 5e or higher24 AWG shielded, 100ohmMolex-MAMolex-F Molex-F Molex-MBCable: CAT 5e,26 AWG stranded,shielded, 100ohmCGroundRing TerminalSecured to LockMounting Plate4-PinWiring to TIA-568-B Standard4-PinEPoELockDApproved SoftwareNotes:• Connectors go on only oneway. They cannot be placedin an incorrect position.• Do not force and do notoffset connectors.• Be sure they are completelyseated (flush).02/11/114 A7763B
Profile Series v.S1 PoE Cylindrical LockA Frame Harness InstallationSupplied by CICut end / ceiling-side PoE harness:Suggested installation of components and wire harness supplied by McKinney:B-SpliceCrimp ConnectorTIA-568-B Standard WiringCeiling24AWGStrandedWire forEarthGroundinside15' FrameHarnessFrame-SideHarnessAssembly(15' length)RJ45-MCable: CAT 5e or higher24 AWG shielded, 100ohm1234Pair Number Wire PIN1 White/Blue2 White/Orange3 White/Green4 White/BrownWhite/Blue 5Blue 4White/Orange 1Orange 2White/Green 3Green 6White/Brown 7Brown 8Do not confuse pair numbers with pin numbers. A pair number is used forreference only (e.g.: 10Base-T Ethernet uses pairs 2 & 3). The pin numbersindicate actual physical locations on the plug and jack.Hinge side of PoE harness:567 81. Feed cut end of harness into hole on hinge-side through single access hole.2. Push one of the connectors back through hole and feed into separateaccess hole.BCabledrain wireconcealedin shrinktubingFrameMolex-MPoE Data Hinge4-pin M6-pin M4-pin F6-pin FEach of the hinge-side harness connectors should end up threaded througha different access hole and matched to the same size pin connector fromthe door harness:• 4-pin male Molex connector.• 6-pin male Molex connector with ground wire.Drain WirePoE Hinge (Patent Pending)Hinge-side harness connectors:• 4-pin male molex connector• 6-pin male molex connector with ground wireLock-side harness connectors:• Ring terminal• (2) 4-pin connectors• 4-pin Molex connector• 4-pin connectorNotes:• Connectors go on only one way. They cannot beplugged to incorrect position.• Do not force and do not offset connectors.• Be sure they are completely seated (flush).Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved.Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.A7763B 502/11/11
Page 2: Table of Contents123456789Warning..
Page 7 and 8: Profile Series v.S1 PoE Cylindrical
Page 15: Profile Series v.S1 PoE Cylindrical

v.S1 Cylindrical Lock Installation Instructions 1.10 - Access Control ...

Create successful ePaper yourself

Delete template?

Save as template?