product manual for Intex Round Above Ground Pool Sand ... - Meijer

More documents

Recommendations

Info

Meijer.com(163) MODEL CS15110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/08/2011English163POOL INLET - NOZZLE & PLUNGER VALVE SETUP1. In a counter-clockwise motion unscrewplunger valve union from the threadedstrainer connector (33) (see drawing 5).Be careful not to lose the step rubberwasher (30). Place the plunger valve onthe ground in a safe place.2. In a counter-clockwise motion unscrew thestrainer nut (31) from the threadedconnector (33). Leave the flat washer (32)on the connector (33).3. Install the nozzle and plunger valve at theupper position of pool inlet. From the insideof the pool liner insert the connector (33)into one of the pre-cut holes with thewasher remaining on the connector to beplaced against the inside of the liner wall.4. Before assembly, lubricate the threads witha petroleum jelly. With the flat side of thestrainer nut (31) facing the outside wall ofthe liner in a clockwise motion screw thestrainer nut (31) back onto the threadedconnector (33) (see drawing 6).5. Finger tighten the adjustable pool inletnozzle (34) and the strainer nut (31) ontothe threaded connector (33).6. Grasp the plunger valve assembly. Makesure the step washer (30) is in place.7. In a clockwise motion screw the plungervalve union back onto the threadedconnector (33) (see drawing 7).8. Examine the plunger valve to see if thehandle is pushed fully down to the "0/1"position. If not, then grasp the handle atthe top and push down turning the handlein a clockwise direction until the plasticprotruding notch anchors in the "0/1"position. This will prevent water fromflowing out during filling (seedrawings 8.1 & 8.2).9. Adjust the direction of nozzle head pointingaway from the pool outlet for a bettercirculation result (see drawing 9).10. The pool liner is now ready to fill withwater. Consult the above-ground-poolowner’s manual for filling instructions.311221INSIDELINER WALL32 33 3412WATERFLOWINSIDELINERWALL5678.18.29SETUP INSTRUCTIONSPOOLSAVE THESE INSTRUCTIONS Page 10
Meijer.com(163) MODEL CS15110 SAND FILTER PUMP & FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 11/08/2011English163PRODUCT SPECIFICATIONSThe sand filter removes suspended particles and sanitize your pool. Poolchemistry is a specialized area and you should consult your local poolservice specialist for details.Power:110-120 Volt ACAmperage:Saltwater System - 0.9 A; Filter Pump - 3 AWattage:Saltwater System - 100 W; Filter Pump - 370 WIdeal Salt Level:3000 ppm (parts per million)Maximum Sanitizer Output/hour: 10 grams/hourCopper Ionizer Output Current: 175mAMaximum working pressure:3.5 bar (50 psi)Effective filtering area: 0.1 m 2 (1.1 ft 2 )Maximum Flow Rate:6050 liters/hour (1600 gallons/hour)Recommended filtering media:No. 20 silica sand or glass sand. Particle size(Not included)range 0.45 to 0.85 mm (0.018 to 0.033 inches).Uniformity Coefficient less than 1.75.Recommended filtering media quantity: No. 20 silica sand 25 Kg (55 Lbs) or glass sand18 Kg (40 Lbs).Limited Warranty:see “Limited Warranty”SETUP INSTRUCTIONSTOOLS REQUIRED: One (1) Phillips screwdriverPump location and mounting:• The system must be installed on a solid level and vibration-free base.• Provide a location protected from the weather, moisture, flooding andfreezing temperature.• Provide adequate access, space and lighting for routine maintenance.• Pump motor requires free circulation of air for cooling. Do not installthe pump in a damp or non-ventilated location.A team of 2 or more people is recommended for setting up this product.Motor pre-filtering assembly setup:1. Remove the sand filter and its accessoriesfrom the packaging carefully and inspect forany visible damage. If parts are damagedcontact your local service center listed at theback of this owner’s manual.2. In a counter-clockwise motion unscrew the leaftrap cover (14) from the pre-filter housing. Takeout the basket (16) and filter housing nut (17)(see drawing 10).3. Connect the pre-filter housing to the motorwater inlet. Note: Align the connector in thepre-filter housing with the water inlet on themotor (see drawing 11).144116171011PRODUCT SPECS & SETUP INSTRUCTIONSSAVE THESE INSTRUCTIONS Page 11
Page 3 and 4: Meijer.com(163) MODEL CS15110 SAND
Page 9: Meijer.com(163) MODEL CS15110 SAND
Page 15: Meijer.com(163) MODEL CS15110 SAND
Page 18 and 19: ECIRCULATEMeijer.comBCLOSEWASTERECI
Page 40: (163) MODEL CS15110 SAND FILTER PUM

product manual for Intex Round Above Ground Pool Sand ... - Meijer

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?