VICE &PROTÃGÃ MANUAL VERSION 2.0 - Bob Long Technologies

More documents

Recommendations

Info

ADJUSTING THE TRIGGERThe Gen 5 Intimidator trigger has two adjustment screws. The bottomscrew is for trigger post-travel and the top screw adjusts the activationpoint (where the marker fires). To adjust the screws insert a hex keyand turn the screw. The screws have Loctite to prevent theadjustment from slipping so a firm, steady pressure is needed for theadjustment.REPLACING/UPGRADINGThe stock trigger is similar to the S-class trigger. However, the stocktrigger does not have a roller bearing. To replace the trigger with an S-class trigger remove the grip frame then remove the retaining screwfrom the left side of the grip frame.The trigger can be removed and a replacement inserted. Make sure toinstall the spring on the new trigger. The S-class trigger has a new pivotscrew and a spacer, which goes between the trigger and the right side ofthe grip frame. The spacer is shown in the picture below.CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR VICE.SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
ADJUSTING THE ASA (FRONT/BACK)The Air Source Adapter (ASA) that connects your high pressure air tank to your Vice is a direct mount ASA. Directmount ASA systems have screws that attach directly to the bottom of the grip frame. This ASA can be adjustedforward or backwards to help position the tank so that it is comfortable for you.1. Loosen the four set screws in the ASA thenlower it from the mounting studs. Notice thesmiley face integrated into the milling? Prettycool, eh?2. Adjust the mounting screw positions forwardsor backwards to achieve the position you prefer.Make sure to leave two empty holes betweeneach stud.3. Snug the studs in place. Don’t use excessiveforce. Optionally use a drop of blue Loctiteinstead to prevent them from coming loose.Additionally a drop of Loctite will help securethe four set screws in the ASA.4. A dovetail mount ASA, such as the Bob LongCam Drive ASA, is secured by set screws whichare accessed via the inside of the grip frame.NOTE: Not all of the holes in the bottom of theframe are accessible from inside the gripframe. Use of a Dovetail mounting ASA requiresone or two 10-32 x ¼” socket set screws. Theseare not installed with the marker from thefactory but are readily available from mosthardware stores for less than $1.5. Depending on the change in the ASA positionyour macroline hose may need to be replaced.When cutting a piece of macro line make surethe cut is smooth and perpendicular to thelength of the hose. Cutting a macro line tooshort will result in a poor connection and a leakfrom the fitting. Using a tool with curved cuttingsurfaces will help ensure a solid cut as shown inthe picture.6. Install an air tank and check for any leaks withthe ASA in the new position. If it helps remindyou – change the holes, check your hose!1 23 45CAUTION: READ ALL WARNINGS BEFORE USING OR ATTEMPTING ANY WORK ON YOUR VICE.SHOULD YOU BE UNSURE AT ANY POINT, STOP AND SEEK PROFESSIONAL SUPPORT.
Page 1: GEN 5INTIMIDATORVICE & PROTÉGÉ MA
Page 4 and 5: QUICK STARTINSTALLING AIR TANKMuch
Page 8 and 9: MAINTAINING THE EYES AND DETENTSIn
Page 10 and 11: SETTING HPR PRESSUREThe HPR pressur
Page 12 and 13: MAINTAINING THE POPPET VALVE ASSEMB
Page 14 and 15: O-RINGS AND FASTENERSO-RINGSPart Na
Page 16 and 17: O-Ring Size Table1x3mm1x4.5mm1x12mm
Page 18 and 19: 11. Q: Should my air hose be squeez
Page 20 and 21: TROUBLESHOOTING GUIDEMarker will no

VICE &PROTÃGÃ MANUAL VERSION 2.0 - Bob Long Technologies

Create successful ePaper yourself

Delete template?

Save as template?

VICE &PROTÃGÃ MANUAL VERSION 2.0 - Bob Long Technologies