TALEXXconverter LCI 60 W 700/1050 mA TEC SR - Tridonic

More documents

Recommendations

Info

LED control gearCompact fixed outputSpecific technical dataTypeOutputcurrentPowerfactor at fullload 1Efficiencyat fullload 1Power Efficiencyfactor at at min.min. load 1 load 1Min. outputvoltage 1Max. outputvoltage 1Max. outputvoltage (noloadvoltage)Max. repetitiveoutput peakcurrent at fullload 12Max. repetitiveoutput peakcurrent at min.load 12Max. nonrepetitiveoutputpeak current atfull load 12Max. nonrepetitiveoutputpeak current atmin. load 12Max. casingtemperature tcLCI 60W 700mA TEC SR 700 mA 0.98 91.5 % 0.93C 90 % 46.5 V 85.5 V 92 V 950 mA 1,100 mA 1,050 mA 1,150 mA 80 °CLCI 60W 1050mA TEC SR 1,050 mA 0.98 90.5 % 0.93C 89 % 31.0 V 57.0 V 62 V 1,420 mA 1,640 mA 1,420 mA 1,650 mA 85 °C1Test result at 230 V, 50 Hz.2The trend between min. and full load is linear.Data sheet 01/15-LC036-7Subject to change without notice.www.tridonic.com 2
LED control gearCompact fixed outputStandardsEN 55015EN 60598-1EN 61000-3-2EN 61000-3-3EN 61347-1EN 61347-2-13EN 61547EN 62384Overload protectionIf the output voltage range is exceeded the LED control gear reduces the LEDoutput current. After elimination of the overload the nominal operation isrestored automatically.Overtemperature protectionThe LED control gear is protected against temporary thermal overheating. If thetemperature limit is exceeded the output current is reduced to limit tc at acertain level. It restarts automatically. The temperature protection is activatedtypically at 8 °C above tc max.Short-circuit behaviourIn case of a short circuit on the secondary side (LED) the LED control gear switchesinto hic-cup mode. After elimination of the short circuit the nominal operation isrestored automatically.No-load operationThe LED control gear works in constant voltage mode. In no-load operation theoutput voltage will not exceed the specified max. output voltage (see page 2).Installation instructionsThe LED module and all contact points within the wiring must be sufficientlyinsulated against 5.0 kV surge voltage.Air and creepage distance must be maintained.Fixing conditionsDry, acidfree, oilfree, fatfree. It is not allowed to exceed the maximum ambienttemperature (ta) stated on the device. Minimum distances stated below arerecommendations and depend on the actual luminaire. Is not suitable for fixingin corner.LeuchteLuminaire>100 mm>20 mmStorage conditionsHumidity: 5 % up to max. 85 %not condensed(max. 56 days/year at 85 %)Storage temperature: -40 °C up to max. +80 °C>50 mmThe devices have to be within the specified temperature range (ta) before theycan be operated.Replace LED module1. Mains off2. Remove LED module3. Wait for 10 seconds4. Connect LED module againHot plug-in or secondary switching of LEDs is not permitted and may cause avery high current to the LEDs.Expected life-timeType ta 40 °C 50 °C 60 °CLCI 60W 700mA TEC SRtc 70 °C 80 °C xLife-time 50,000 h 30,000 h xLCI 60W 1050mA TEC SRtc 75 °C 85 °C xLife-time 50,000 h 30,000 h xThe LED Drivers are designed for a life-time stated above under referenceconditions and with a failure probability of less than 10 %.Maximum loading of automatic circuit breakersAutomatic circuitC10 C13 C16 C20 B10 B13 B16 B20 Inrush currentbreaker typeInstallation Ø 1.5 mm 2 1.5 mm 2 1.5 mm 2 2.5 mm 2 1.5 mm 2 1.5 mm 2 1.5 mm 2 2.5 mm 2 Imax TimeLCI 60W 700mA TEC SR 20 30 40 50 16 24 32 40 13 A 50 µsLCI 60W 1050mA TEC SR 20 30 40 50 16 24 32 40 13 A 50 µsHarmonic distortion in the mains supply (at 230 V / 50 Hz and full load) in %THD 3. 5. 7. 9. 11.LCI 60W 700mA TEC SR 20 7 3 2 1 1LCI 60W 1050mA TEC SR 20 5 2 1 1 1Data sheet 01/15-LC036-7Subject to change without notice.www.tridonic.com 3
Page 1: LED control gearCompact fixed outpu
Page 5 and 6: LED control gearCompact fixed outpu

TALEXXconverter LCI 60 W 700/1050 mA TEC SR - Tridonic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?