GSM Data Modem AT Command Guide - Scotec - GiSMo Modem

More documents

Recommendations

Info

“CUSTOM” User defined character set (cf. +WCCS command).“HEX” Hexadecimal mode. No character set used ; the user can read or writehexadecimal values.4.6 GiSMo Phonebook Character Set +WPCS4.6.1 Description :This specific command informs the ME which character set is used by the TE for the phonebooks.The ME can convert each character of entered or displayed strings. This is used to read or writephonebook entries. See also +CSCS for the short messages character sets.4.6.2 Syntax :Command syntax : AT+WPCS=CommandAT+WPCS=”TRANSPARENT”Note : Transparent modeAT+WPCS=”CUSTOM”Note : Custom character setAT+WPCS=?Note : Get possible valuesPossible responsesOKNote : Command validOKNote : Command valid+WPCS: ("TRANSPARENT","HEX","CUSTOM")OKNote : Possible values4.6.3 Defined values :“TRANSPARENT”“CUSTOM”“HEX”Transparent mode. The strings are displayed and entered as they arestored in SIM or in ME.User defined character set (cf. +WCCS command).Hexadecimal mode. No character set used ; the user can read or writehexadecimal values.4.7 Request IMSI +CIMI4.7.1 Description :This command is used to read and identify the IMSI (International Mobile Subscriber Identity) of theSIM card. The PIN may need to be entered before reading the IMSI.4-16
4.7.2 SyntaxCommand syntax :CommandAT+CIMINote : Read the IMSIAT+CIMISee appendix 18.12 for MCC / MNC description.Possible responses208200120320598Note : IMSI value (15 digits), starting with MCC (3digits) / MNC (2 digits, 3 for PCS 1900)4.8 Card Identification +CCID4.8.1 Description :This command orders the product to read the EF-CCID file on the SIM card.4.8.2 Syntax :Command syntax :CommandAT+CCIDNote : Get card IDAT+CCID?Note : Get current valueAT+CCIDPossible responses+CCID: “123456789AB111213141”Note : EF-CCID is present, hexadecimal format+ CCID: “123456789AB111213141”Note : Same result as +CCIDAT+CCID= ?Note : Get possible valueOKNote : No parameter but this command is validIf there is no EF-CCID file present on the SIM, the +CCID answer will not be sent, but the OKmessage will be returned.4.9 Capabilities list +GCAP4.9.1 Description :This command gets the complete list of capabilities.4.9.2 Syntax :Command syntax : AT+GCAPCommandAT+GCAPNote : Get capabilities listPossible responses+GCAP: +CGSM +FCLASSOKNote : Supports GSM and FAX commands4.10 Repeat last command A/4.10.1 Description :This command repeats the previous command. Only the A/ command itself cannot be repeated.4-17
Page 1 and 2: GiSMoGSM Data ModemAT Command Guide
Page 3 and 4: 5 Call Control commands ...........
Page 5 and 6: 10.11 Price per unit and currency t
Page 7 and 8: 15.15 GiSMo Voice Rate +WVR .......
Page 9 and 10: 25.10 Class 2 Commands.............
Page 11 and 12: 1.4 DefinitionsThe words, “Mobile
Page 13 and 14: 3 General behaviors3.1 SIM Insertio
Page 15: 4.3.2 Syntax :Command syntax : AT+C
Page 19 and 20: AT+CFUN=0Note : Set minimum functio
Page 21 and 22: 4.16.2 Syntax :Command syntax :Comm
Page 23 and 24: 4.19 Ringer Sound Level +CRSL4.19.1
Page 25 and 26: ATD>SM6;Note : Call index 6 from AN
Page 27 and 28: 5.5.2 Syntax :Command syntax : AT+C
Page 29 and 30: DTR switches ONNote : The number in
Page 31 and 32: 5.11 Single Numbering Scheme +CSNS5
Page 35 and 36: 5.15.2 Syntax :Command syntax :AT+E
Page 39 and 40: 6 Network service commands6.1 Signa
Page 41 and 42: CommandAT+COPS?Note : Ask for curre
Page 43 and 44: 6.4.2 Syntax :Command syntax:Respon
Page 45 and 46: 7 Security commands7.1 Enter PIN +C
Page 47 and 48: CommandAT+CPBS=”FD”Note : Choos
Page 49 and 50: 7.4 Facility lock +CLCK7.4.1 Descri
Page 53 and 54: 8.2 Read phonebook entries +CPBR8.2
Page 59 and 60: Using mode 4 and 5 with +CPBF comma
Page 61 and 62: 8.8.2 Syntax :Command syntax : AT+W
Page 63 and 64: 9 Short Messages commands9.1 Parame
Page 65 and 66: Note:PDU is entered using format i
Page 67 and 68:
9.5 Preferred Message Format +CMGF9
Page 69 and 70:
9.7.2 Syntax :Command syntax : AT+C
Page 71 and 72:
: sets the result code indication r
Page 73 and 74:
9.11.2 Syntax :Command syntax : AT+
Page 75 and 76:
The message reference, , which is r
Page 77 and 78:
9.15.3 Defined values :The byte co
Page 79 and 80:
9.17 Service center address +CSCA9.
Page 81 and 82:
9.20 Message status modification +W
Page 83 and 84:
10 Supplementary Services commands1
Page 85 and 86:
“AO”, “OI”, “OX” barrin
Page 87 and 88:
10.5 Calling line identification re
Page 89 and 90:
CommandAT+COLP=1Note : Activate COL
Page 91 and 92:
Page 93 and 94:
10.12.3 Defined values0: Release al
Page 95 and 96:
1: closed User Group call, with CUG
Page 97 and 98:
11 Data commands11.1 Using AT Comma
Page 99 and 100:
11.3 Select mode +FCLASS11.3.1 Desc
Page 101 and 102:
Page 103:
11.9.2 Syntax :Command syntax : AT%
Page 106 and 107:
12 Fax commandsThe fax service prov
Page 108 and 109:
12.4 HDLC receive speed +FRH12.4.1
Page 110 and 111:
13 Fax class 2 commandsIf the featu
Page 112 and 113:
CommandAT+FBOR=?Note : Test command
Page 114 and 115:
13.10.3 Defined values :This comman
Page 116 and 117:
CommandAT+FLID=?Note : Test command
Page 118 and 119:
14 V24-V25 commands14.1 Fixed DTE r
Page 120 and 121:
14.3 DTE-DCE local flow control +IF
Page 122 and 123:
14.6.2 Syntax :Command syntax : AT&
Page 124 and 125:
14.11.2 Syntax :Command syntax : AT
Page 126 and 127:
14.16 Request identification inform
Page 128 and 129:
15 Specific AT commands15.1 Cell en
Page 130 and 131:
128 (bit-7): Network lost indicatio
Page 132 and 133:
For ADC A, the value returned inclu
Page 134 and 135:
: Keyboard map is (5,5)0 1 2 3 45 6
Page 136 and 137:
15.10 Input/Output Management +WIOM
Page 138 and 139:
15.12.3 Defined values :0: Stop pla
Page 140 and 141:
AT+WVR=AT+WVR=?If Half Rate availab
Page 142 and 143:
15.17.2 Syntax :Command syntax : AT
Page 144 and 145:
15.20.2 Syntax :Command syntax: AT+
Page 146 and 147:
Page 148 and 149:
15.25 GiSMo Software version +WSSW1
Page 150 and 151:
Page 152 and 153:
Syntax : +WVMI: ,Option :1: Line 12
Page 154 and 155:
15.30 GiSMo Battery Charge Manageme
Page 156 and 157:
15.30.4.3 Defined values0: Minimum
Page 158 and 159:
11 or "MONO900": Mono-band mode 900
Page 160 and 161:
15.33.2 SyntaxCommand syntaxCommand
Page 162 and 163:
15.36 GiSMo Open AT control command
Page 164 and 165:
“000:00”- “168:59”15.38 Set
Page 166 and 167:
AT+WLOC?The location is in mode aut
Page 168 and 169:
15.40 GiSMo Bus Read +WBR15.40.1 De
Page 170 and 171:
Data buffer to write on the specifi
Page 172 and 173:
15.43.3 Defined values :decimal val
Page 174 and 175:
16.1.5 Data Download to SIMData dow
Page 176 and 177:
16.3 SIM TOOLKIT COMMANDS16.3.1 SIM
Page 178 and 179:
16.3.2 SIM ToolKit Indication (+STI
Page 180 and 181:
Table 1CmdTypeDescriptionPossible r
Page 182 and 183:
0: Echo off.1: Echo on. (1-255)Mini
Page 184 and 185:
+STIN: 0OKAT+STGI=0+STGI: ”SIM TO
Page 186 and 187:
Values when CmdType=3 (Get Input)0:
Page 188 and 189:
17 Other AT commands17.1 V.25 ter r
Page 190 and 191:
18.2 Message service failure result
Page 192 and 193:
252 Call barring on outgoing calls2
Page 194 and 195:
18.9 Intermediate result codesVerbo
Page 196 and 197:
Parameters storage modeCommandAT&W(
Page 198 and 199:
Parameters storage modeCommandAT&W(
Page 200 and 201:
18.11.3 Call barring*SC*Password# o
Page 202 and 203:
CZ 230 01 CZ PAEGAS PAEGASCZ 230 02
Page 204 and 205:
LT 246 02 LT BITE GSM BITELTU 246 0
Page 206 and 207:
TWN 466 93 Mobitai TW MOBTWN 466 97
Page 208 and 209:
ZW 648 01 ZW NET*ONE NET*118-208
Page 210 and 211:
Data packets can have different val
Page 212 and 213:
When a voice call is attempted from
Page 214 and 215:
19.2.3 Example 3 : Find phonebook e
Page 216 and 217:
19.4.2 Example 2: Receive a fax cla
Page 218 and 219:
TABLE 2 -Compatibility between avai
Page 220:
Fifth byte (Event driven informatio
Page 223 and 224:
- Octet 5 indicates a UCS2 characte
Page 225 and 226:
25 APPENDIX G : Conditions for comm
Page 227 and 228:
AT+CCWA +WIND: 4 Y NAT+CLIR +WIND:
Page 229 and 230:
AT+ADC None N NAT+CMER None N NAT+W
show all

GSM Data Modem AT Command Guide - Scotec - GiSMo Modem

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?