GSM Data Modem AT Command Guide - Scotec - GiSMo Modem

More documents

Recommendations

Info

0 Disable1 Enable2 Interrogate3 Registration4 Erasure1 Voice2 Data3 Fax4 Short Messages5 All classesNote:The combination of different classes is not supported, it will only result in the activation / deactivation/ status request of all classes (7).In the case where the FDN phonebook is activated, the registration is restricted to the phonenumbers written in the FDN. not managed not managed For = 2 (No reply), 4 (all call forwarding) and 5 (all conditional callforwarding), time to wait (1 to 30) in seconds before call is forwarded. Default value is 20.10.2 Call barring +CLCK10.2.1 Description :This command allows control of the call barring supplementary service.Locking, unlocking or querying the status of call barring is possible for all classes or for a specificclass.10.2.2 Syntax :Command Syntax : AT+CLCK= , [, [, ] ]Response Syntax: (for =2 and command successful)+CLCK: [, [ +CLCK: , [… ] ]CommandPossible responsesAT+CLCK=”AO”,1,1234Note :AT+CLCK=”AO”,0,5555Note :AT+CLCK=”AO”,0,1234Note :OKNote : Command valid+CME ERROR: 16Note : Wrong passwordOKNote : Command valid10-84
“AO”, “OI”, “OX” barring for outgoing calls“AI”, “IR”barring for incoming calls“AG”, “AC”,”AB” for all calls barring (=0 only)0: Unlocks the facility1: Locks the facility2: Query status : see description for +CLCK command (Facility lock) or +CCFC (Call forwarding).A combination of different classes is not supported. It will only result in the activation / deactivation/ status request for all classes (7).The password code is over 4 digits maximum.10.3 Modify SS password +CPWD10.3.1 Description :This command is used by the application to change the supplementary service password.10.3.2 Syntax :Command Syntax: AT+CPWD=,, for see +CLCK command with only “P2”facility added (SIM PIN2).CommandPossible responsesAT+CPWD=”AO”,1234,5555Note : Change Call Barring passwordAT+CPWD=”AO”,1234,5555Note : Change passwordAT+CPWD=”AO”,5555,1234Note : Change passwordOKNote : Password changed+CME ERROR: 16Note : Wrong passwordOKNote : Password changedWhatever the facility, the change of password applies to all call barring.10.4 Call waiting +CCWA10.4.1 Description :This command allows control of the call waiting supplementary service.The product will send a +CCWA unsolicited result code when the call waiting service is enabled.10-85
Page 1 and 2:
GiSMoGSM Data ModemAT Command Guide
Page 3 and 4:
5 Call Control commands ...........
Page 5 and 6:
10.11 Price per unit and currency t
Page 7 and 8:
15.15 GiSMo Voice Rate +WVR .......
Page 9 and 10:
25.10 Class 2 Commands.............
Page 11 and 12:
1.4 DefinitionsThe words, “Mobile
Page 13 and 14:
3 General behaviors3.1 SIM Insertio
Page 15 and 16:
4.3.2 Syntax :Command syntax : AT+C
Page 17 and 18:
4.7.2 SyntaxCommand syntax :Command
Page 19 and 20:
AT+CFUN=0Note : Set minimum functio
Page 21 and 22:
4.16.2 Syntax :Command syntax :Comm
Page 23 and 24:
4.19 Ringer Sound Level +CRSL4.19.1
Page 25 and 26:
ATD>SM6;Note : Call index 6 from AN
Page 27 and 28:
5.5.2 Syntax :Command syntax : AT+C
Page 29 and 30:
DTR switches ONNote : The number in
Page 31 and 32:
5.11 Single Numbering Scheme +CSNS5
Page 33 and 34: 5.12.2 Syntax :Command syntax :Comm
Page 35 and 36: 5.15.2 Syntax :Command syntax :AT+E
Page 37 and 38: 5.16.2 Syntax :Command syntax :Comm
Page 39 and 40: 6 Network service commands6.1 Signa
Page 41 and 42: CommandAT+COPS?Note : Ask for curre
Page 43 and 44: 6.4.2 Syntax :Command syntax:Respon
Page 45 and 46: 7 Security commands7.1 Enter PIN +C
Page 47 and 48: CommandAT+CPBS=”FD”Note : Choos
Page 49 and 50: 7.4 Facility lock +CLCK7.4.1 Descri
Page 51 and 52: 7.5.2 Syntax :Command syntax : AT+C
Page 53 and 54: 8.2 Read phonebook entries +CPBR8.2
Page 59 and 60: Using mode 4 and 5 with +CPBF comma
Page 61 and 62: 8.8.2 Syntax :Command syntax : AT+W
Page 63 and 64: 9 Short Messages commands9.1 Parame
Page 65 and 66: Note:PDU is entered using format i
Page 67 and 68: 9.5 Preferred Message Format +CMGF9
Page 71 and 72: : sets the result code indication r
Page 73 and 74: 9.11.2 Syntax :Command syntax : AT+
Page 75 and 76: The message reference, , which is r
Page 77 and 78: 9.15.3 Defined values :The byte co
Page 79 and 80: 9.17 Service center address +CSCA9.
Page 81 and 82: 9.20 Message status modification +W
Page 83: 10 Supplementary Services commands1
Page 87 and 88: 10.5 Calling line identification re
Page 89 and 90: CommandAT+COLP=1Note : Activate COL
Page 93 and 94: 10.12.3 Defined values0: Release al
Page 95 and 96: 1: closed User Group call, with CUG
Page 97 and 98: 11 Data commands11.1 Using AT Comma
Page 99 and 100: 11.3 Select mode +FCLASS11.3.1 Desc
Page 103: 11.9.2 Syntax :Command syntax : AT%
Page 106 and 107: 12 Fax commandsThe fax service prov
Page 108 and 109: 12.4 HDLC receive speed +FRH12.4.1
Page 110 and 111: 13 Fax class 2 commandsIf the featu
Page 112 and 113: CommandAT+FBOR=?Note : Test command
Page 114 and 115: 13.10.3 Defined values :This comman
Page 116 and 117: CommandAT+FLID=?Note : Test command
Page 118 and 119: 14 V24-V25 commands14.1 Fixed DTE r
Page 120 and 121: 14.3 DTE-DCE local flow control +IF
Page 122 and 123: 14.6.2 Syntax :Command syntax : AT&
Page 124 and 125: 14.11.2 Syntax :Command syntax : AT
Page 126 and 127: 14.16 Request identification inform
Page 128 and 129: 15 Specific AT commands15.1 Cell en
Page 130 and 131: 128 (bit-7): Network lost indicatio
Page 132 and 133: For ADC A, the value returned inclu
Page 134 and 135:
: Keyboard map is (5,5)0 1 2 3 45 6
Page 136 and 137:
15.10 Input/Output Management +WIOM
Page 138 and 139:
15.12.3 Defined values :0: Stop pla
Page 140 and 141:
AT+WVR=AT+WVR=?If Half Rate availab
Page 142 and 143:
15.17.2 Syntax :Command syntax : AT
Page 144 and 145:
15.20.2 Syntax :Command syntax: AT+
Page 146 and 147:
Page 148 and 149:
15.25 GiSMo Software version +WSSW1
Page 150 and 151:
Page 152 and 153:
Syntax : +WVMI: ,Option :1: Line 12
Page 154 and 155:
15.30 GiSMo Battery Charge Manageme
Page 156 and 157:
15.30.4.3 Defined values0: Minimum
Page 158 and 159:
11 or "MONO900": Mono-band mode 900
Page 160 and 161:
15.33.2 SyntaxCommand syntaxCommand
Page 162 and 163:
15.36 GiSMo Open AT control command
Page 164 and 165:
“000:00”- “168:59”15.38 Set
Page 166 and 167:
AT+WLOC?The location is in mode aut
Page 168 and 169:
15.40 GiSMo Bus Read +WBR15.40.1 De
Page 170 and 171:
Data buffer to write on the specifi
Page 172 and 173:
15.43.3 Defined values :decimal val
Page 174 and 175:
16.1.5 Data Download to SIMData dow
Page 176 and 177:
16.3 SIM TOOLKIT COMMANDS16.3.1 SIM
Page 178 and 179:
16.3.2 SIM ToolKit Indication (+STI
Page 180 and 181:
Table 1CmdTypeDescriptionPossible r
Page 182 and 183:
0: Echo off.1: Echo on. (1-255)Mini
Page 184 and 185:
+STIN: 0OKAT+STGI=0+STGI: ”SIM TO
Page 186 and 187:
Values when CmdType=3 (Get Input)0:
Page 188 and 189:
17 Other AT commands17.1 V.25 ter r
Page 190 and 191:
18.2 Message service failure result
Page 192 and 193:
252 Call barring on outgoing calls2
Page 194 and 195:
18.9 Intermediate result codesVerbo
Page 196 and 197:
Parameters storage modeCommandAT&W(
Page 198 and 199:
Parameters storage modeCommandAT&W(
Page 200 and 201:
18.11.3 Call barring*SC*Password# o
Page 202 and 203:
CZ 230 01 CZ PAEGAS PAEGASCZ 230 02
Page 204 and 205:
LT 246 02 LT BITE GSM BITELTU 246 0
Page 206 and 207:
TWN 466 93 Mobitai TW MOBTWN 466 97
Page 208 and 209:
ZW 648 01 ZW NET*ONE NET*118-208
Page 210 and 211:
Data packets can have different val
Page 212 and 213:
When a voice call is attempted from
Page 214 and 215:
19.2.3 Example 3 : Find phonebook e
Page 216 and 217:
19.4.2 Example 2: Receive a fax cla
Page 218 and 219:
TABLE 2 -Compatibility between avai
Page 220:
Fifth byte (Event driven informatio
Page 223 and 224:
- Octet 5 indicates a UCS2 characte
Page 225 and 226:
25 APPENDIX G : Conditions for comm
Page 227 and 228:
AT+CCWA +WIND: 4 Y NAT+CLIR +WIND:
Page 229 and 230:
AT+ADC None N NAT+CMER None N NAT+W
show all

GSM Data Modem AT Command Guide - Scotec - GiSMo Modem

Create successful ePaper yourself

Delete template?

Save as template?