GSM Data Modem AT Command Guide - Scotec - GiSMo Modem

More documents

Recommendations

Info

5.14 Speaker & Microphone selection +SPEAKER5.14.1 DescriptionThis specific command is used to select the speaker and the microphone set.5.14.2 Syntax :Command syntax :CommandAT+SPEAKER=Possible responsesAT+SPEAKER=0OKNote : Speaker ONE and Micro ONENote : Command validAT+SPEAKER? +SPEAKER: 0OKNote : Speaker ONE and Micro ONE are active5.14.3 Defined values :0 : SPEAKER ONE, MICRO ONE1 : SPEAKER TWO, MICRO TWO5.15 Echo Cancellation +ECHO5.15.1 Description :This specific command is used to enable, disable or configure the Echo Cancellation functions forvoice calls (in rooms, in cars, etc.).It is necessary to tune the Microphone gain (AT+VGT) and the Speaker gain (AT+VGR) beforeactivating the Echo Cancellation.5-34
5.15.2 Syntax :Command syntax :AT+ECHO= [,, ,,,,,]CommandPossible responsesAT+CMEE=1OKNote: Enables the use of result codeAT+SPEAKER? + SPEAKER: 0OKNote : Speaker ONE and Micro ONE are activeAT+SIDET=0OKNote: Deactivate the SidetoneAT+SIDET? +SIDET: 0,0AT+ECHO?+ECHO: 0,1,0,3,10,7Note : Read current settingsOKAT+ECHO=1,1,0,3,10,7OKNote : Active Echo cancellation 1 for Mic/Spk one.AT+ECHO?+ECHO: 1,1,0,3,10,7Note : Read current settingsOKAT+ECHO=1,3,30,8000,256+CME ERROR: 519Note : Activate the Echo cancellation 3Note : The new algorithm will be activated after areset of the productAT+ECHO?+ECHO: 3,3,30,8000,256Note : Read the Echo cancellation settingsOKAT+CFUN=1OKNote: Reset the productAT+ECHO?+ECHO: 1,3,30,8000,256Note : Read current settingsAT+ECHO=0Note: Deactivate the Echo CancellationOKOK5.15.3 Defined values:0 : Deactivate Echo1 : Activate Echo1 : Echo cancellation 13 : Echo cancellation 3 (optional)5-35
Page 1 and 2: GiSMoGSM Data ModemAT Command Guide
Page 3 and 4: 5 Call Control commands ...........
Page 5 and 6: 10.11 Price per unit and currency t
Page 7 and 8: 15.15 GiSMo Voice Rate +WVR .......
Page 9 and 10: 25.10 Class 2 Commands.............
Page 11 and 12: 1.4 DefinitionsThe words, “Mobile
Page 13 and 14: 3 General behaviors3.1 SIM Insertio
Page 15 and 16: 4.3.2 Syntax :Command syntax : AT+C
Page 17 and 18: 4.7.2 SyntaxCommand syntax :Command
Page 19 and 20: AT+CFUN=0Note : Set minimum functio
Page 21 and 22: 4.16.2 Syntax :Command syntax :Comm
Page 23 and 24: 4.19 Ringer Sound Level +CRSL4.19.1
Page 25 and 26: ATD>SM6;Note : Call index 6 from AN
Page 29 and 30: DTR switches ONNote : The number in
Page 31 and 32: 5.11 Single Numbering Scheme +CSNS5
Page 33: 5.12.2 Syntax :Command syntax :Comm
Page 37 and 38: 5.16.2 Syntax :Command syntax :Comm
Page 39 and 40: 6 Network service commands6.1 Signa
Page 41 and 42: CommandAT+COPS?Note : Ask for curre
Page 43 and 44: 6.4.2 Syntax :Command syntax:Respon
Page 45 and 46: 7 Security commands7.1 Enter PIN +C
Page 47 and 48: CommandAT+CPBS=”FD”Note : Choos
Page 49 and 50: 7.4 Facility lock +CLCK7.4.1 Descri
Page 53 and 54: 8.2 Read phonebook entries +CPBR8.2
Page 59 and 60: Using mode 4 and 5 with +CPBF comma
Page 61 and 62: 8.8.2 Syntax :Command syntax : AT+W
Page 63 and 64: 9 Short Messages commands9.1 Parame
Page 65 and 66: Note:PDU is entered using format i
Page 67 and 68: 9.5 Preferred Message Format +CMGF9
Page 71 and 72: : sets the result code indication r
Page 73 and 74: 9.11.2 Syntax :Command syntax : AT+
Page 75 and 76: The message reference, , which is r
Page 77 and 78: 9.15.3 Defined values :The byte co
Page 79 and 80: 9.17 Service center address +CSCA9.
Page 81 and 82: 9.20 Message status modification +W
Page 83 and 84: 10 Supplementary Services commands1
Page 85 and 86:
“AO”, “OI”, “OX” barrin
Page 87 and 88:
10.5 Calling line identification re
Page 89 and 90:
CommandAT+COLP=1Note : Activate COL
Page 91 and 92:
10.9.2 Syntax :Command syntax : AT+
Page 93 and 94:
10.12.3 Defined values0: Release al
Page 95 and 96:
1: closed User Group call, with CUG
Page 97 and 98:
11 Data commands11.1 Using AT Comma
Page 99 and 100:
11.3 Select mode +FCLASS11.3.1 Desc
Page 101 and 102:
11.6.2 Syntax :Command syntax : AT+
Page 103:
11.9.2 Syntax :Command syntax : AT%
Page 106 and 107:
12 Fax commandsThe fax service prov
Page 108 and 109:
12.4 HDLC receive speed +FRH12.4.1
Page 110 and 111:
13 Fax class 2 commandsIf the featu
Page 112 and 113:
CommandAT+FBOR=?Note : Test command
Page 114 and 115:
13.10.3 Defined values :This comman
Page 116 and 117:
CommandAT+FLID=?Note : Test command
Page 118 and 119:
14 V24-V25 commands14.1 Fixed DTE r
Page 120 and 121:
14.3 DTE-DCE local flow control +IF
Page 122 and 123:
14.6.2 Syntax :Command syntax : AT&
Page 124 and 125:
14.11.2 Syntax :Command syntax : AT
Page 126 and 127:
14.16 Request identification inform
Page 128 and 129:
15 Specific AT commands15.1 Cell en
Page 130 and 131:
128 (bit-7): Network lost indicatio
Page 132 and 133:
For ADC A, the value returned inclu
Page 134 and 135:
: Keyboard map is (5,5)0 1 2 3 45 6
Page 136 and 137:
15.10 Input/Output Management +WIOM
Page 138 and 139:
15.12.3 Defined values :0: Stop pla
Page 140 and 141:
AT+WVR=AT+WVR=?If Half Rate availab
Page 142 and 143:
15.17.2 Syntax :Command syntax : AT
Page 144 and 145:
15.20.2 Syntax :Command syntax: AT+
Page 146 and 147:
Page 148 and 149:
15.25 GiSMo Software version +WSSW1
Page 150 and 151:
Page 152 and 153:
Syntax : +WVMI: ,Option :1: Line 12
Page 154 and 155:
15.30 GiSMo Battery Charge Manageme
Page 156 and 157:
15.30.4.3 Defined values0: Minimum
Page 158 and 159:
11 or "MONO900": Mono-band mode 900
Page 160 and 161:
15.33.2 SyntaxCommand syntaxCommand
Page 162 and 163:
15.36 GiSMo Open AT control command
Page 164 and 165:
“000:00”- “168:59”15.38 Set
Page 166 and 167:
AT+WLOC?The location is in mode aut
Page 168 and 169:
15.40 GiSMo Bus Read +WBR15.40.1 De
Page 170 and 171:
Data buffer to write on the specifi
Page 172 and 173:
15.43.3 Defined values :decimal val
Page 174 and 175:
16.1.5 Data Download to SIMData dow
Page 176 and 177:
16.3 SIM TOOLKIT COMMANDS16.3.1 SIM
Page 178 and 179:
16.3.2 SIM ToolKit Indication (+STI
Page 180 and 181:
Table 1CmdTypeDescriptionPossible r
Page 182 and 183:
0: Echo off.1: Echo on. (1-255)Mini
Page 184 and 185:
+STIN: 0OKAT+STGI=0+STGI: ”SIM TO
Page 186 and 187:
Values when CmdType=3 (Get Input)0:
Page 188 and 189:
17 Other AT commands17.1 V.25 ter r
Page 190 and 191:
18.2 Message service failure result
Page 192 and 193:
252 Call barring on outgoing calls2
Page 194 and 195:
18.9 Intermediate result codesVerbo
Page 196 and 197:
Parameters storage modeCommandAT&W(
Page 198 and 199:
Parameters storage modeCommandAT&W(
Page 200 and 201:
18.11.3 Call barring*SC*Password# o
Page 202 and 203:
CZ 230 01 CZ PAEGAS PAEGASCZ 230 02
Page 204 and 205:
LT 246 02 LT BITE GSM BITELTU 246 0
Page 206 and 207:
TWN 466 93 Mobitai TW MOBTWN 466 97
Page 208 and 209:
ZW 648 01 ZW NET*ONE NET*118-208
Page 210 and 211:
Data packets can have different val
Page 212 and 213:
When a voice call is attempted from
Page 214 and 215:
19.2.3 Example 3 : Find phonebook e
Page 216 and 217:
19.4.2 Example 2: Receive a fax cla
Page 218 and 219:
TABLE 2 -Compatibility between avai
Page 220:
Fifth byte (Event driven informatio
Page 223 and 224:
- Octet 5 indicates a UCS2 characte
Page 225 and 226:
25 APPENDIX G : Conditions for comm
Page 227 and 228:
AT+CCWA +WIND: 4 Y NAT+CLIR +WIND:
Page 229 and 230:
AT+ADC None N NAT+CMER None N NAT+W
show all

GSM Data Modem AT Command Guide - Scotec - GiSMo Modem

Create successful ePaper yourself

Delete template?

Save as template?