Wind Design Considerations for Steel Joists and Joist Girders - SEAoT

More documents

Recommendations

Info

Steel Joist Design20K6 Rod Web @ 40’-0”With (net) uplift -108 plf84 plf8’-0” 32’-0”Bottom Chord = 2 angles 1.5 x 1.5 x 0.155, A = 0.882 in. 2End Web = 7/8 in. dia. round bar , A = 0.601 in. 2SEAoT State Conference November 6-8, 2008 Houston TX SEAoT - 84
Steel Joist DesignDesign DataEnd Web, left end l = 37.49 in.KLrFcrFcrΩ0.9===0.877F( 37.49)0.80.21875e8.02 ksi== 137.10.877( 137.1)PA2π E= 13.35 ksi3.550.601c( 8.02) = 7.21ksi > = = 5.90 ksi ∴OK2Reduce to 90% for eccentricity at bearing seatSEAoT State Conference November 6-8, 2008 Houston TX SEAoT - 85
Page 2 and 3:
Introduction‣ Commercial manufact
Page 4 and 5:
Windstorm Damage to Roof in Texas05
Page 6 and 7:
Hurricane Charley Category 4 StormA
Page 8 and 9:
Population Trends in Hurricane-Pron
Page 10:
Roof Design to Resist Uplift Loads
Page 15 and 16:
2005 SJI Standard Specification for
Page 17 and 18:
2005 SJI Code of Standard Practice1
Page 20 and 21:
2005 SJI Code of Standard Practice6
Page 23 and 24:
2006 International Building Code•
Page 25 and 26:
Standards and Codes• 2005 SJI Sta
Page 27 and 28:
ASCE 7-05 Basic Wind Speed MapSEAoT
Page 29 and 30:
ASCE 7-05 Specified Wind LoadsSEAoT
Page 31 and 32:
ASCE 7-05 Specified Wind LoadsWhat
Page 33 and 34: ASCE 7-05 Specified Wind Loads• M
Page 36 and 37: Properly Applying Wind Loads toStee
Page 38 and 39: Properly Applying Wind Loads toStee
Page 41 and 42: Wind Design Considerations forSteel
Page 43 and 44: Wind Design Considerations forSteel
Page 45 and 46: Properly Applying Lateral Loads toS
Page 47 and 48: Properly Applying Lateral Loads toS
Page 49 and 50: Typical Roof Framing using K-Series
Page 51 and 52: Profile of SJI Standard K-SeriesOpe
Page 53 and 54: Joist Seat Test Program Parameters
Page 55 and 56: Experimental Test SetupINSTRUMENTAT
Page 57 and 58: Typical Load-Deformation BehaviorTe
Page 59 and 60: Yield Line PatternsShort and Long A
Page 61 and 62: Yield Line Analysis Using Virtual W
Page 63 and 64: Research Programs Recommendations
Page 65 and 66: 2005 SJI Standard Specification for
Page 67 and 68: P n = 2 M p L yl / aASD Design Proc
Page 69 and 70: Recommended Bearing Seat Designto R
Page 71 and 72: Recommended Bearing Seat Designto R
Page 77 and 78: Design ExampleDimensions:Length, l
Page 79 and 80: Design ExampleBasic wind speed, fro
Page 81 and 82: Steel Joist and Joist Girder Layout
Page 83: Steel Joist Design20K6 Rod Web @ 40
Page 87 and 88: Placement of Bridging to ResistUpli
Page 93 and 94: Summary and Conclusions• Wind for
Page 95: Any Questions?SJI Website: http://w
show all

Wind Design Considerations for Steel Joists and Joist Girders - SEAoT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?