40-138M.pdf - Pickering Interfaces

More documents

Recommendations

Info

SECTION 1 - TECHNICAL SPECIFICATIONpickering40-138 Mixed Relay ConfiguratorWhen ordering a configuration of mixed relays, each cell canbe set to be populated by SPST, DPST, SPDT or DPDT. Thepart number is in the form 40-138-aa-bb-cc-dd where:aa is the number of SPST relays (multiples of 6)bb is the number of DPST relays (multiples of 3)cc is the number of SPDT relays (multiples of 4)dd is the number of DPDT relays (multiples of 2)For further assistance consult the Operating Manual, web siteor contact sales office.Relay Type Cells 1 to 13 Cell 13 custom build†SPST 6 per cell 8DPST 3 per cell 4SPDT 4 per cell 4DPDT 2 per cell 2† Note: Cell 13 is configured as the same size as other cells except oncustom builds.40-138 Mixed Relay Configuration ExampleA typical mixed relay example is shown in the followingtable where the specified configuration is; 12 x SPST, 15x DPST, 16 x SPDT and 4 x DPDT. This corresponds tothe order code: 40-138-12-15-16-4. SPST switches arealways installed in the lowest cell number and DPDT arealways installed in the highest populated cell number.For further assistance please contact sales office.RelayTypeCell 1Cell 2Cell 3Cell 4Cell 5Cell 6Cell 7Cell 8Cell 9Cell 10Cell 11Cell 12Cell 13TotalSPST 6 6 6 6 6 6 6 6 6 6 6 6 8 12DPST 3 3 3 3 3 3 3 3 3 3 3 3 4 15SPDT 4 4 4 4 4 4 4 4 4 4 4 4 4 16DPDT 2 2 2 2 2 2 2 2 2 2 2 2 2 4A1C1A2C2A3C3A4C4A5C5A6C6A7C7A8C8A9C9A10C10A11C11A12C12A1.1The above configuration is shown in the diagram below.C1.1A1.2C1.2A2.1A9.1B1B9C2.1C9.1A1A9A2.2A9.2C1C9B1.1C2.2C9.2A1.1A3.1A10.1B2B10C1.1C3.1C10.1A2A10B1.2A3.2A10.2C2C10A1.2C3.2C10.2B3B11C1.2A4.1A11.1A3A11C4.1C11.1B2.1C3C11A4.2A11.2A2.1C4.2C11.2B4B12C2.1A5.1A12.1A4A12B2.2C5.1C12.1C4C12A2.2A5.2A12.2C2.2B5B13C5.2C12.2A5A13B3.1A6.1A13.1C5C13A3.1C6.1C13.1C3.1A6.2A13.2B6B14B3.2C6.2C13.2A6A14A3.2A7.1A14.1C6C14C3.2C7.1C14.1B7B15A7.2A14.2B4.1A7A15C7.2C14.2A4.1C7C15A8.1A15.1C4.1C8.1A8.2C8.2C15.1A15.2C15.2B8A8C8B16A16C16B4.2A4.2C4.212 x SPST 15 x DPST 16 x SPDT 4 x DPDTSchematic Diagram for the 40-138 Module With an Example Mixed Relay Configuration (40-138-12-15-16-4)Page 1.2HIGH DENSITY 2A VERSATILE RELAY MODULE 40-138pickeringtest.com
pickeringSECTION 1 - TECHNICAL SPECIFICATIONRelay Type & Maintenance40-138 series modules are fitted with electro-mechanical signalrelays, palladium-ruthenium, gold covered contacts.The module is of a single circuit board construction and usesthrough hole relays (not SMT relays) so field maintenance isgreatly simplified. In addition a Spare Relay is built onto thecircuit board to facilitate easy maintenance with minimumdowntime.Switch Specification (all versions)Switch Type:Contact Type:Max Switch Voltage:Max Power:Max Switch Current:Max Continuous Carry Current:Max Pulsed Carry Current Example(for a single switch path):Initial Path ResistanceOn:Off:Minimum Voltage:Thermal Offset:Operate Time:Expected Life (operations)Very low power signal load:Low power load (2W):Medium power load (30W):Full power load (60W):Electro-mechanicalPalladium-Ruthenium,Gold Covered Bifurcated300VDC/250VAC62.5VA, 60W from 30Vto 220VDC, 30W to300VDC (resistive load)2A2A6A for 100ms(up to 10% duty cycle)< 500mΩ(1Ameasurement condition)< 600mΩ (10mAmeasurement condition)> 10 9 Ω100µV< 10µV< 3ms> 10 8> 1.5x10 7 (0.1A 20VDC)> 5x10 6 (1A, 30VDC)> 1x10 5 (2A, 30VDC)> 1x10 5 (0.1A, 300VDC)Power Requirements+3.3V +5V +12V -12V0 2.6A max(80 relays energised)0 0Mechanical CharacteristicsSingle slot 3U PXI (CompactPCI card).3D models for all versions in a variety of popular file formatsare available on request.ConnectorsPXI bus via 32-bit P1/J1 backplane connector.Signals via front panel 160-Way DIN 41612 male connector, forpin outs please refer to the operating manual.We recommend that Pickering mating connectors are usedwith this module which are designed to ensure there are nomechanical interference problems when used in a PXI chassis.Mixed Relay Configuration Order CodesPart numbers are in the form:40-138-aa-bb-cc-ddWhere:aa is the number of SPSTbb is the number of DPSTcc is the number of SPDTdd is the number of DPDTPlease note that these configurations are shipped withproduct codes in the form of ‘40-138-XXX’, where ‘XXX’contains digits reflecting the specific manufacturing build.Support ProductsSpare Relay KitsKits of replacement relays are available for the majority of Pickering’sPXI switching modules, simplifying servicing and reducing down-time.The relay kit for the 40-138 range is as follows:91-100-001 kit for 40-138-XXX(where XXX are three digits that correspond to the specificmanufacturing build of the module)For further assistance, please contact your local Pickering sales office.Mating Connectors & CablingFor connection accessories for the 40-138 series pleaserefer to the 90-001D 160-way DIN 41612 ConnectorAccessories data sheet where a complete list anddocumentation can be found for accessories, or refer to theConnection Solutions catalog.40-138 Module Side ViewHIGH DENSITY 2A VERSATILE RELAY MODULE 40-138pickeringtest.comPage 1.3
Page 1 and 2: pickeringUser ManualHigh Density 2A
Page 3 and 4: pickeringpickeringteChNICal sUPPort
Page 5: pickeringCONTENTSCopyright Statemen
Page 10 and 11: SECTION 1 - TECHNICAL SPECIFICATION
Page 12 and 13: SECTION 2 - TECHNICAL DESCRIPTIONpi
Page 14 and 15: SECTION 2 - TECHNICAL DESCRIPTIONpi
Page 16 and 17: SECTION 3 - INSTALLATIONpickeringSO
Page 18 and 19: SECTION 4 - PROGRAMMING GUIDEpicker
Page 20 and 21: SECTION 4 - PROGRAMMING GUIDEpicker
Page 22 and 23: SECTION 5 - CONNECTOR INFORMATIONpi
Page 32 and 33: SECTION 6 - TROUBLE SHOOTINGpickeri
Page 34 and 35: SECTION 7 - MAINTENANCE INFORMATION
Page 36 and 37: SECTION 7 - MAINTENANCE INFORMATION
Page 38 and 39: pickeringTHIS PAGE INTENTIONALLY BL
Page 40 and 41: APPENDIX A - EXAMPLE CONNECTOR PINO
Page 54: APPENDIX A - EXAMPLE CONNECTOR PINO

40-138M.pdf - Pickering Interfaces

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?