Gates Industrial Hose - Wright, F. B.

More documents

Recommendations

Info

WARNINGGates Corporation recommends industrial hoses for normal service as described in this catalog. Other applications should be referred to your respective marketingrepresentative.In any application, there may be inherent risk of bodily injury or property damage and the user is responsible for implementation of adequate safety precautions.It is the responsibility of the person supplying the hose to advise the user of proper instructions for the adequate safe use and/or precautions andto warn the user of consequences of failure to heed such instruction. Should a hose assembly fail during use because of excessive pressure, injurious and/ordamaging chemicals, elevated temperature materials, explosives or flammable materials, then serious bodily injury or destruction of property could resultfrom impelled couplings, whipping hose, high pressure or high velocity discharge, chemical contact, high temperature materials, explosion or fire.In known high risk areas, it is recommended that hose inspections be performed at frequent intervals related to the risk factor. Hose with obvious damage shouldbe scrapped and replaced. These inspections should include tube and cover conditions, leaking or slipped couplings and proof test.Detailed information concerning storage, care and maintenance may be found in the Hose Handbook published by Association for Rubber Products Manufacturers1901 Pennsylvania Avenue, N.W., Washington, D.C. 20006 and in SAE Recommended Practices J1273.IMPORTANTGates recommends only those applications of products specified in Gates product literature.Gates disclaims any liability for use of its products in applications other than those for which they were designed.Service LifeAll rubber products, including Industrial Hose assemblies, have a limited lifeon a given application. Assuming the correct hose has been selected for theapplication, this service life can be adversely affected by many variable conditions.The major ones are:— Exposure to severe external abuse such as kinking, bending, high endpull, crushing or abrasion.— Exposure to higher-than-rated working pressures or to high surgepressures.— Exposure to higher-than rated temperatures.— Misapplication or exposure to corrosive liquids or gases outside therange of suitable applications.1. External abuse—hoses should be placed where they will not be runover by equipment or subjected to high end pull. Hoses should not bebent below recommended minimum bend radius. This could result inkinking the hose or reducing its pressure resistance. Large diameterhoses also may require additional support to reduce external abuse.2. Hose & System Pressures—In establishing and determining pressuresrelated to hose and the systems to which they are applied, it is necessaryto consider separately the characteristics of the hose and the system.— The system (or device or application) can have several pressures dependingon pressure sources and surges imposed by the operator ormechanical components.— A given hose has a fixed characteristic with respect to the pressure itcan withstand (and how it is applied) and still give satisfactory life.3. High Temperatures—The allowable temperature ranges for industrialhoses are shown on the High Temperature Ranges page. These are forproduct temperatures and should not be exceeded. High temperaturescan degrade rubber stocks very quickly resulting in short service life.Where external temperatures are higher than normal ambient, contactyour Gates field representative for recommendations.4. Misapplication—All industrial hoses are designed for a certain specificapplication or related application. They should not be used for any otherapplications.5. Hose Information—Refer to the following pages for details of hoseconstruction and physical characteristics. These are shown in the datapages and include such items as rated working pressure, vacuum rating,minimum bend radius and static conductivity.6. Internal Abrasion—For applications of a highly abrasive nature wherethe hose makes one or more bends, hose should be rotated 90º periodicallyto lengthen service life.The hose manufacturer established, through design and testing, the recommendedrated working pressure for the hose. It is the responsibility of the userto accurately determine the system pressure. Steady state pressure can bemeasured readily by gauges. Surges are difficult to measure and may requirethe use of electronic pressure pickup devices. Also, surge values depend onso many variables that a series of tests are usually required to obtain a validset of readings. However, if there are extreme surges in the normal operation,or if there is the likelihood of abnormal operation of the system, the magnitudemust be determined.Considering the recommended rated working pressure of the HOSE and thevarious pressures of the SYSTEM, the hose is matched to the system usingproper application engineering principles. End terminations may reduce therated working pressure of hose assemblies. Refer to coupling manufacturerfor recommendations.GATES CORPORATION LIMITED WARRANTYGoods are warranted to be free from defects in material or workmanship for thelife of the Goods (or the published recommended replacement interval specifiedby Gates). Gates will replace or repair, at its option, any Goods proved defectivein material or workmanship during the warranty period. This is the sole remedyfor breach of warranty. Color fade and color difference is not warranted. Thiswarranty is void if the defect is caused by improper installation, use ormaintenance of the Goods, or used for racing or competition. Goods are notwarranted to comply with laws that may apply to uses of the Goods not stated inrelated materials, e.g., use in manned or unmanned aviation or life supportapplications. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,INCLUDING, BUT NOT LIMITED TO WARRANTIES OF MERCHANT-ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AREEXPRESSLY DISCLAIMED. FAILURE TO REPLACE TIMING BELTSOR OTHER GATES PRODUCTS AS SPECIFIED MAY RESULT INCATASTROPHIC ENGINE OR EQUIPMENT DAMAGE, FOR WHICHGATES DISCLAIMS ALL RESPONSIBILITY, TO THE EXTENTPERMITTED BY APPLICABLE LAW.Some states do not allow the exclusion or limitation of incidental or consequentialdamages, and some states do not allow limitations on how long an impliedwarranty lasts, so the above limitation and exclusion may not apply to you. Thiswarranty gives you specific legal rights, and you may also have other rightswhich vary from state to state.Powering Progress. gates.com/industrialhose 9
GATES INDUSTRIAL HOSE PRODUCTSCUT LENGTH PROGRAMGates Industrial Hose Cut Length Program offers distributors easy access to customcut length hoses. Over 150 large I.D. standard-stock industrial hose products areavailable in this program. It includes our most popular hose lines as well as those thatmay not typically be stocked.Thanks to this program, you never have to pass up an order for special lengths ofGates Industrial Hose.HOW IT WORKS...1. Your customer has a special request for a specific length of cut hose.*2. Check the inventory list to be sure the hose is available for customcut lengths.3. Call Gates Customer Service with your order – 800-366-3128.4. Your cut length hose will ship in two days or less.Expedited one-day shipping is available.The Gates Industrial Hose Cut Length Program lets you bring a completepackage of Gates industrial hose products and services to your customers to meetevery need.For more information: Contact your Gates Customer Service Representative.*Any length less than standard is available and there is no minimum length charge.Standard freight terms will apply. Pricing will include a 20% premium overcustomer’s class net price.10gates.com/industrialhoseGates Corporation
Page 1 and 2: HOSE, COUPLINGS + EQUIPMENT2012 IND
Page 3 and 4: GATES INDUSTRIAL HOSE PRODUCTSCANCE
Page 5 and 6: GATES INDUSTRIAL HOSE PRODUCTSTERMS
Page 7 and 8: GATES INDUSTRIAL HOSE PRODUCTSStain
Page 9: GATES INDUSTRIAL HOSE PRODUCTSSubje
Page 13 and 14: GATES INDUSTRIAL HOSE PRODUCTSCUT L
Page 15 and 16: GATES INDUSTRIAL HOSE PRODUCTSSELEC
Page 17 and 18: GATES INDUSTRIAL HOSE PRODUCTSAppli
Page 19 and 20: GATES INDUSTRIAL HOSE PRODUCTS1. Ha
Page 21 and 22: GATES INDUSTRIAL HOSE PRODUCTSHose
Page 23 and 24: GATES INDUSTRIAL HOSE PRODUCTSGATES
Page 25 and 26: GATES INDUSTRIAL HOSE PRODUCTSGATES
Page 27 and 28: GATES INDUSTRIAL HOSE PRODUCTSACID-
Page 61 and 62:
GATES INDUSTRIAL HOSE PRODUCTSACID-
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
GATES INDUSTRIAL HOSE PRODUCTSHigh
Page 139 and 140:
GATES INDUSTRIAL HOSE PRODUCTSHigh
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
GATES INDUSTRIAL HOSE PRODUCTSHose
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229:
POWERING PROGRESS GATES CORPORATION
show all

Gates Industrial Hose - Wright, F. B.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?