M 90A2 - Tohatsu

More documents

Recommendations

Info

Fig. 4INTAKE SILENCER・CARBURETOR11
Q’tyRef.No. Part No. Description RemarksM<strong>90A2</strong>4-1 3B7-02410-0 INTAKE SILENCER SUB-ASSY 14-2 3B7-67152-0 CHOKE LEVER 14-3 941403-1000 WAVE WASHER d=10 14-4 910103-0610 BOLT 14-5 346-67115-0 WASHER 6.5-21-1 14-6 910103-0630 BOLT 14-7 930103-0600 NUT 14-8 3B7-63734-0 STOPPER DAMPER 14-9 3B7-72015-0 CHOKE DECAL 14-10 346-02414-2 INTAKE SILENCER GASKET 34-11 345-02417-1 INTAKE SILENCER LOCK PLATE 34-12 910121-0618 BOLT 64-13 3B7-02415-0 INTAKE SILENCER COVER 14-14 3B7-02418-1 GASKET 14-15 910103-5620 BOLT 84-16 1 3L9-03200-0 CARBURETOR ASSY 1 Upper4-16 2 3L9-03207-0 CARBURETOR ASSY (SECOND) 1 Center4-16 3 3L9-03210-0 CARBURETOR ASSY (THIRD) 1 Lower4-17 353-03221-0 * FLOAT CHAMBER 14-18 346-03222-0 * FLOAT CHAMBER O-RING 1 x 34-19 922503-6414 * SCREW 4 x 34-20 346-03231-0 * FLOAT 1 x 34-21 346-03232-0 * FLOAT ARM PIN 1 x 34-22 3B7-03240-0 * FLOAT VALVE 1 x 34-23 344-03244-0 * CLIP 1 x 34-24 3F3-03234-0 * SCREW 1 x 34-25 3L9-03252-0 * MAIN NOZZLE 1 x 34-26 3B7-03251-0 * MAIN JET (#150) 1 x 34-27 3C7-03255-0 * SLOW JET (#75) 1 x 3Upper, Center, Lowerx 312
Page 3 and 4: 9. Hose, that is a standard part, i
Page 5 and 6: Fig. 1CYLINDER・CRANK CASEFig. 2PI
Page 8 and 9: Fig. 1CYLINDER・CRANK CASE1
Page 14 and 15: Fig. 2PISTON・CRANK SHAFT7
Page 16 and 17: Fig. 3INTAKE MANIFOLD・REED VALVE9
Page 20 and 21: Fig. 4INTAKE SILENCER・CARBURETOR1
Page 22 and 23: Fig. 5FUEL LINE15
Page 24 and 25: Fig. 6THROTTLE17
Page 26 and 27: Fig. 7MAGNETO19
Page 28 and 29: Fig. 8ELECTRIC PARTS (C.D. UNIT)21
Page 30 and 31: Fig. 8ELECTRIC PARTS (C.D. UNIT)23
Page 32 and 33: Fig. 9ELECTRIC PARTS (STARTER MOTOR
Page 34 and 35: Fig. 9ELECTRIC PARTS (STARTER MOTOR
Page 36 and 37: Fig. 10OIL PUMP (AUTO MIXING)29
Page 38 and 39: Fig. 10OIL PUMP (AUTO MIXING)31
Page 40 and 41: Fig. 11DRIVE SHAFT HOUSING33
Page 42 and 43: Fig. 11DRIVE SHAFT HOUSING35
Page 44 and 45: Fig. 12GEAR CASE (DRIVE SHAFT)37
Page 50 and 51: Fig. 13GEAR CASE (PROPELLER SHAFT)4
Page 52 and 53: Fig. 13GEAR CASE (PROPELLER SHAFT)4
Page 54 and 55: Fig. 14BRACKET47
Page 62 and 63: Fig. 15POWER TRIM & TILT (PTT)55
Page 64 and 65: Fig. 15POWER TRIM & TILT (PTT)57
Page 66 and 67: Fig. 16BOTTOM COWL59
Page 68 and 69:
Fig. 16BOTTOM COWL61
Page 70 and 71:
Fig. 17SHIFT63
Page 72 and 73:
Fig. 18TOP COWL65
Page 74 and 75:
Fig. 19FUEL TANK67
Page 76 and 77:
Fig. 20COMPONENT PARTS OF REMOTE CO
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Fig. 22ACCESSORIES75
Page 84 and 85:
77Fig. 23 OPTIONAL PARTS (1)
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Fig. 25ASSEMBLY・KIT PARTS83
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
INDEXADJUST SCREW. ................
Page 98 and 99:
MOUNT HOLDING PLATE (LOWER) .... 14
Page 100 and 101:
YOKE ASSY .........................
Page 102 and 103:
3B7-09053-1. . . . . . . . 10-113B7
Page 105 and 106:
Copyright © 2013 Tohatsu Corporati
show all

M 90A2 - Tohatsu

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?