M 90A2 - Tohatsu

More documents

Recommendations

Info

Fig. 10OIL PUMP (AUTO MIXING)29
Ref.No. Part No. DescriptionQ’tyM<strong>90A2</strong>Remarks10-1 3B7-09000-1 OIL PUMP ASSY 110-2 3B7-09002-0 * O-RING 1.6-19.2 110-3 3B7-09004-0 * AIR VENT BOLT 110-4 3B7-09006-0 * WASHER 110-5 3B7-09050-0 OIL PUMP BOLT 210-6 941303-0600 SPRING WASHER 210-7 3B7-09065-0 OIL PUMP DRIVEN GEAR 110-8 3B7-09069-0 BUSHING 9-20-20.8 110-9 99AA-4-0480 PIPE 110-10 3C7-09056-1 CLIP φ8.5 2Oil Pump-Check Valve99AA-4-100010-11 3B7-09053-1 OIL PUMP ROD 110-12 3B7-05243-0 BALL JOINT CONNECTOR 210-13 930103-0500 NUT 210-14 951703-0500 SNAP RETAINER d=5 210-15 3B7-71010-2 OIL TANK 110-16 3C8-71015-0 OIL FILLER CAP 110-17 3C8-71016-0 GASKET 36-52-2 110-18 3C8-71017-0 CAP HOOK 110-19 3C8-71018-0 OIL TANK CAP CHECK VALVE 110-20 3B7-71020-1 OIL LEVEL SENSOR 110-21 910103-0630 BOLT 310-22 346-67115-0 WASHER 6.5-21-1 610-23 941303-0600 SPRING WASHER 310-24 346-67113-0 MOUNT 8.5-14-2.5 310-25 3B7-06920-0 RUBBER MOUNT 8.5-14-2.5 310-26 346-67114-1 SPACER 6.2-9-15.7 310-27 3C7-71030-0 OIL FILTER ASSY 110-28 3B7-02237-0 * CUP 110-29 3B7-02235-0 * O-RING 130
Page 3 and 4: 9. Hose, that is a standard part, i
Page 5 and 6: Fig. 1CYLINDER・CRANK CASEFig. 2PI
Page 8 and 9: Fig. 1CYLINDER・CRANK CASE1
Page 14 and 15: Fig. 2PISTON・CRANK SHAFT7
Page 16 and 17: Fig. 3INTAKE MANIFOLD・REED VALVE9
Page 18 and 19: Fig. 4INTAKE SILENCER・CARBURETOR1
Page 20 and 21: Fig. 4INTAKE SILENCER・CARBURETOR1
Page 22 and 23: Fig. 5FUEL LINE15
Page 24 and 25: Fig. 6THROTTLE17
Page 26 and 27: Fig. 7MAGNETO19
Page 28 and 29: Fig. 8ELECTRIC PARTS (C.D. UNIT)21
Page 30 and 31: Fig. 8ELECTRIC PARTS (C.D. UNIT)23
Page 32 and 33: Fig. 9ELECTRIC PARTS (STARTER MOTOR
Page 34 and 35: Fig. 9ELECTRIC PARTS (STARTER MOTOR
Page 38 and 39: Fig. 10OIL PUMP (AUTO MIXING)31
Page 40 and 41: Fig. 11DRIVE SHAFT HOUSING33
Page 42 and 43: Fig. 11DRIVE SHAFT HOUSING35
Page 44 and 45: Fig. 12GEAR CASE (DRIVE SHAFT)37
Page 50 and 51: Fig. 13GEAR CASE (PROPELLER SHAFT)4
Page 52 and 53: Fig. 13GEAR CASE (PROPELLER SHAFT)4
Page 54 and 55: Fig. 14BRACKET47
Page 62 and 63: Fig. 15POWER TRIM & TILT (PTT)55
Page 64 and 65: Fig. 15POWER TRIM & TILT (PTT)57
Page 66 and 67: Fig. 16BOTTOM COWL59
Page 68 and 69: Fig. 16BOTTOM COWL61
Page 70 and 71: Fig. 17SHIFT63
Page 72 and 73: Fig. 18TOP COWL65
Page 74 and 75: Fig. 19FUEL TANK67
Page 76 and 77: Fig. 20COMPONENT PARTS OF REMOTE CO
Page 82 and 83: Fig. 22ACCESSORIES75
Page 84 and 85: 77Fig. 23 OPTIONAL PARTS (1)
Page 86 and 87:
79Fig. 23 OPTIONAL PARTS (1)
Page 88 and 89:
81Fig. 24 OPTIONAL PARTS (2)
Page 90 and 91:
Fig. 25ASSEMBLY・KIT PARTS83
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
INDEXADJUST SCREW. ................
Page 98 and 99:
MOUNT HOLDING PLATE (LOWER) .... 14
Page 100 and 101:
YOKE ASSY .........................
Page 102 and 103:
3B7-09053-1. . . . . . . . 10-113B7
Page 105 and 106:
Copyright © 2013 Tohatsu Corporati
show all

M 90A2 - Tohatsu

Create successful ePaper yourself

Delete template?

Save as template?