M 90A2 - Tohatsu

More documents

Recommendations

Info

Fig. 14BRACKET47
Ref.No. Part No. DescriptionQ’tyM<strong>90A2</strong>Remarks14-1 3E0-62191-1 SWIVEL BRACKET SHAFT ASSY 1 Bracket Bolt14-2 346-62124-1 NYLON NUT 7/8-14 114-3 344-67177-1 GREASE FITTING 114-4 940103-0600 WASHER 114-5 3E0Q62112-0 CLAMP BRACKET (R) 1 Starboard Side14-6 3E0Q62113-1 CLAMP BRACKET (L) 1 Port Side14-7 9102E3-1020 BOLT 114-8 9402E3-1000 WASHER 214-9 3E0-62121-1 THRUST ROD 114-10 3B7-62129-1 PIN 114-11 3E0Q62313-3 SWIVEL BRACKET ASSY 114-12 344-67177-1 * GREASE FITTING 414-13 9101E3-5612 * BOLT 414-14 3E0-62116-1 WASHER 25.7-50-1 214-15 3E0-62126-0 BUSHING 25.6-28.6-40 214-16 3B7Q62010-2 STEERING SHAFT ASSY 114-17 3B7-62414-0 SEAL RING 114-18 3B7-62417-0 BUSHING 32-40-45 214-19 3B7-62423-1 THRUST PLATE (UPPER) 214-20 945103-3200 C-RING d=32 114-21 3B7-62415-0 O-RING 4.5-32 114-22 1 3B7-62095-0 STEERING ARM DAMPER L=20 1 for Transom "L"14-22 2 3B7-62096-0 STEERING ARM DAMPER L=40 1 for Transom "UL"14-23 3B7-61301-0 RUBBER MOUNT (UPPER) 214-24 3B7-61307-2 BOLT 7/16-115 214-25 3C7-61338-0 DAMPER 21-36-5 214-26 3B7-61335-0 WASHER 11.5-32-3 214-27 3B7-61341-1 MOUNT HOLDING PLATE (UPPER) 114-28 9101E3-5835 BOLT 348
Page 3 and 4: 9. Hose, that is a standard part, i
Page 5 and 6: Fig. 1CYLINDER・CRANK CASEFig. 2PI
Page 8 and 9: Fig. 1CYLINDER・CRANK CASE1
Page 14 and 15: Fig. 2PISTON・CRANK SHAFT7
Page 16 and 17: Fig. 3INTAKE MANIFOLD・REED VALVE9
Page 18 and 19: Fig. 4INTAKE SILENCER・CARBURETOR1
Page 20 and 21: Fig. 4INTAKE SILENCER・CARBURETOR1
Page 22 and 23: Fig. 5FUEL LINE15
Page 24 and 25: Fig. 6THROTTLE17
Page 26 and 27: Fig. 7MAGNETO19
Page 28 and 29: Fig. 8ELECTRIC PARTS (C.D. UNIT)21
Page 30 and 31: Fig. 8ELECTRIC PARTS (C.D. UNIT)23
Page 32 and 33: Fig. 9ELECTRIC PARTS (STARTER MOTOR
Page 34 and 35: Fig. 9ELECTRIC PARTS (STARTER MOTOR
Page 36 and 37: Fig. 10OIL PUMP (AUTO MIXING)29
Page 38 and 39: Fig. 10OIL PUMP (AUTO MIXING)31
Page 40 and 41: Fig. 11DRIVE SHAFT HOUSING33
Page 42 and 43: Fig. 11DRIVE SHAFT HOUSING35
Page 44 and 45: Fig. 12GEAR CASE (DRIVE SHAFT)37
Page 50 and 51: Fig. 13GEAR CASE (PROPELLER SHAFT)4
Page 52 and 53: Fig. 13GEAR CASE (PROPELLER SHAFT)4
Page 56 and 57: Fig. 14BRACKET49
Page 62 and 63: Fig. 15POWER TRIM & TILT (PTT)55
Page 64 and 65: Fig. 15POWER TRIM & TILT (PTT)57
Page 66 and 67: Fig. 16BOTTOM COWL59
Page 68 and 69: Fig. 16BOTTOM COWL61
Page 70 and 71: Fig. 17SHIFT63
Page 72 and 73: Fig. 18TOP COWL65
Page 74 and 75: Fig. 19FUEL TANK67
Page 76 and 77: Fig. 20COMPONENT PARTS OF REMOTE CO
Page 82 and 83: Fig. 22ACCESSORIES75
Page 84 and 85: 77Fig. 23 OPTIONAL PARTS (1)
Page 90 and 91: Fig. 25ASSEMBLY・KIT PARTS83
Page 96 and 97: INDEXADJUST SCREW. ................
Page 98 and 99: MOUNT HOLDING PLATE (LOWER) .... 14
Page 100 and 101: YOKE ASSY .........................
Page 102 and 103: 3B7-09053-1. . . . . . . . 10-113B7
Page 105 and 106:
Copyright © 2013 Tohatsu Corporati
show all

M 90A2 - Tohatsu

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?