SR13/15 Series - Sensors Tecnics, Honeywell

Solid State Hall EffectPosition SensorsSR13/15 SeriesFEATURES• 3.8 to 30 VDC supplyvoltage• Digital current sinkingoutput• Snap-in or flat mountpackages• Quad-Hall design eliminatesstress effects• Temperature compensatedmagnetics• Bipolar, unipolar andlatching magnetics• High output capability,50mA absolute maximum• Operating temperaturerange -40˜C to +150˜C• Varying leadwire lengths of24 AWG Radox wireThe newly introduced SR13/15 Series package enhancements permit quickand easy sensor installation, increasing the usability of the SS400 Series.These devices can be installed without additional mounting hardware. Thesnap-in and flat mount sensor packages can house any of the presentSS400 Series sensors or any similarly sized sensing elements. Thepackages also provide varying 24AWG Radox leadwire lengths orconnector capabilities.WARNINGPERSONAL INJURY• DO NOT USE theseproducts as safety oremergency stop devices orin any other applicationwhere failure of the productcould result in personalinjury.Failure to comply with theseinstructions could result indeath or serious injury.The SS400 Series position sensors have a thermally balanced integratedcircuit that provides predictable performance for the -40˜C to +150˜Coperating temperature range. The SS400 Series band gap regulationprovides stable operation over 3.8 to 30 VDC. Current consumption is 10mA at +40˜C ambient temperature. SS400 Series sensors are capable ofcontinuous 20 mA sinking output. The sensors may be cycled as high as50 mA maximum. Bipolar, unipolar and latching magnetics are available.WARNINGMISUSE OF DOCUMENTATION• The information presented in this product sheet is for reference only.Do not use this document as product installation information.• Complete installation, operation, and maintenance information isprovided in the instructions supplied with each product.Failure to comply with these instructions could result in death or seriousinjury.Sensing and Control

Solid State Hall EffectPosition SensorSR13/15 SeriesOPERATING CHARACTERISTICS –40°C TO 125°C, 3.8 TO 30 VDCMin. Typ. Max. RemarksSupply voltage 3.8 ⎯ 30 VDCCurrent consumption ⎯ ⎯ 13 mAOutput voltage (operated) ⎯ ⎯ 0.40 Sinking 10 mA max.Sink current (operated) ⎯ ⎯ 20 mAOutput leakage current(released) ⎯ ⎯ 5 µA V OUT= 30 VDC, V CC= 30 VDCOutput switching timeRise, 10 to 90% ⎯ 1.5 µs. 1.5 µs V CC= 12 V, R L= 1.6 KΩ, C L= 20 pFOperating TemperatureFall, 90 to 10% ⎯ 15 µs 1.5 µs-40°C to +150°C (-40°F to +302°F)MAGNETIC CHARACTERISTICSSR13C-A1 SR13D-A1 SR13F-A1 SR13R-A1 SR15C-A3Magnetic Type Unipolar Unipolar Unipolar Latching Unipolar25°CMax. Op. 180 115 390 85 180Min. Rel. 75 20 235 -85 75Min. Dif. 25 20 30 50 25-20°C to 85°CMax. Op. 215 135 435 110 215NOTICEMin. Rel. 60 15 200 -110 60Min. Dif. 10 8 30 50 10Bipolar Hall effect sensors may have an initial output in either the On or Off state if powered up with an appliedmagnetic field in the differential zone (applied magnetic field > Brp and < Bop). Honeywell recommends allowing 10 µsfor output voltage to stabilize after supply voltage has reached 5 volts.BLOCK CIRCUIT WIRING DIAGRAMVs (+)HALLSENSORTRIGGERCIRCUITANDAMPLIFIEROUTPUT(O) N. H.GROUND (-)2 Honeywell • Sensing and Control For application help: call 1-800-537-6945

Solid State Hall EffectPosition SensorsSR13/15 SeriesMOUNTING DIMENSIONS (for reference only) mm/inSNAP-IN DIGITAL POSITION SENSOR (SR13C-A1, SR13D-A21, SR13F-A1, SR13R-A1)To SensorFace0,50.022,50.107,60.30ASSEMBLED INMEXICOC.L. ofSensor2,50.104,80.192,30.095,800.2311,300.44520,30.803,80.153,430.1356,40.253 X 5,10.203 X 152,46.00Red(+) Green(O)Black(-)5,10.20FLAT MOUNT DIGITAL POSITION SENSOR (SR15C-A3)To SensorFace0,50.027,60.30ASSEMBLED INMEXICOC.L. ofSensor2,50.1020,30.803,80.153 X 5,10.203 X 254,010.00Red(+) Green(O)Black(-)5,10.20For application help: call 1-800-537-6945 Honeywell • Sensing and Control 3

Solid State Hall EffectPosition SensorsSR13/15 SeriesSUGGESTED MOUNTING DETAIL3,170.122,80.1111,30.445,10.20WARRANTY/REMEDYHoneywell warrants goodsof its manufacture as beingfree of defective materials andfaulty workmanship. Contactyour local sales office forwarranty information. Ifwarranted goods are returnedto Honeywell during the periodof coverage, Honeywell willrepair or replace withoutcharge those items it findsdefective. The foregoing isBuyer’s sole remedy and is inlieu of all other warranties,expressed or implied,including those ofmerchantability and fitnessfor a particular purpose.Specifications may changewithout notice. Theinformation we supply isbelieved to be accurate andreliable as of this printing.However, we assume noresponsibility for its use.While we provideapplication assistancepersonally, through ourliterature and the Honeywellweb site, it is up to thecustomer to determine thesuitability of the product in theapplication.For application assistance,current specifications, orname of the nearestAuthorized Distributor, contacta nearby sales office. Or call:1-800-537-6945 USA1-800-737-3360 Canada1-815-235-6847 InternationalFAX1-815-235-6545 USAINTERNETwww.honeywell.com/sensinginfo@micro.honeywell.comSensing and ControlHoneywell Inc.11 West Spring StreetFreeport, Illinois 61032Printed with Soy Inkon 50% Recycled Paper005842-1-EN IL50 GLO 999 Printed in USAwww.honeywell.com/sensing