HYDRAULIC SLIDE-OUT MANUAL - Power Gear

GEN­SLIDEHYDRAULIC SLIDE­OUT MANUALPart #: 82­S0298­00Rev 0

TABLE OF CONTENTSSystem Description ........................................................................................ 3System Operation .… ...................................................................................... 3Maintenance ................................................................................................... 4Troubleshooting Hints ................................................................................... 4Parts Listing ................................................................................................... 5How to Order ................................................................................................. 6Limited Warranty ........................................................................................... 7SYSTEM DESCRIPTION2

The Power Gear Gen­Slide system is a hydraulic actuator system designed to provideyears of reliable service. It consists of the following components:­ A bi­directional hydraulic pump.­ A cylinder assembly with piloted locking system.SYSTEM OPERATIONTo extend your generator:1) Make sure the generator path is free of obstacles.2) Push the rocker switch to the “out”position.3) Extend the generator to your satisfaction, then release the switch.To retract your generator:1) Make sure the generator path is free of obstacles.2) Push the rocker switch to the “in”position.3) When the generator is fully retracted, release the switch.SYSTEM MAINTENANCE3

This system uses Type “A”Automatic Transmission Fluid (Dextron III, etc.).Do not fill reservoir with any other type of fluid.The Gen­Slide system is designed to provide years of trouble­free service. To assure thecontinued operation of your Gen­Slide, periodically check the fluid level in the pumpreservoir. This can be done in the fully extended or fully retracted positions.Examine the fluid level, and measure it against the oil level decal on the side of thereservoir, keeping in mind the current position of the generator. If the fluid level is lowerthan the appropriate level line, remove the fill cap on the top of the reservoir and addhydraulic fluid.The Gen­Slide system is a closed hydraulic circuit. If additional fluid is needed, be sureto check the pump, hoses to the cylinder assembly, and the cylinder assembly itself forleakage.NOTE­ With the generator slide­out extended NEVER completely fill the reservoir.This will result in overflow and leaking when the generator slide­out is retracted.TROUBLESHOOTINGIf your Gen­Slide system fails to function, check the system fuse. If the fuse is notdamaged, check the wiring connections on the control switch and to the pump. If theseare all intact, secure your generator in the retracted position and have the system serviced.PARTS LISTING4

Item # Description Part Number1 Gen­Slide Pump/Motor Assembly 5401092 Elbow 07­12513 Cylinder Assembly 5401134 Lock Valve Assembly 5401155 Hose, 48” 08­A0486 Hose, 52” 08­A0527 Hose, 78” 08­A078PARTS ORDERING INFORMATION5

When ordering parts, please provide the following information:1) Your Name2) Your Company’s Name3) Your Phone Number4) Your Shipping Address5) Your Billing Address6) The Purchase Order Number7) The Coach Model NumberFor each part needed, please provide:1) The Part Number2) The Part Description3) The Quantity Required6

POWER GEAR LIMITED WARRANTYPower Gear warrants to the original retail purchaser that the product will be free from defects in materialand workmanship for a period of one (1) year following the retail sales date. Power Gear will, at itsoption, repair or replace any part covered by this limited warranty which, following examination byPower Gear or its authorized distributors or dealers, is found to be defective under normal use andservice. No claims under this warranty will be valid unless Power Gear or its authorized distributor ordealer is notified in writing of such claim prior to the expiration of the warranty period. Warranty isnon­transferable.THIS WARRANTY SHALL NOT APPLY TO:Failures due to normal wear and tear, accident, misuse, abuse, or negligence.Products which are modified or altered in a manner not authorized by Power Gear in writing.Failure due to misapplication of product.Telephone, telegraph, teletype or other communication expenses.Living or travel expenses of person performing service.Overtime labor.Failures created by improper installation of the product’s slideout system or slideout room to includefinal adjustments made at the plant for proper room extension/retraction; sealing interface betweenslideout rooms and side walls; synchronization of inner rails; or improper wiring or groundproblems.Failures created by improper installation of leveling systems, including final adjustments made at theplant, or low fluid level, wiring or ground problems.Replacement of normal maintenance items including lubricants and fuses.There is no other express warranty other than the foregoing warranty. THERE ARE NO IMPLIEDWARRANTIES OF MERCHANTIBILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NOEVENT SHALL POWER GEAR BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIALDAMAGES. This warranty gives you specific legal rights, and you may also have other rights that varyfrom state to state. Some states do not allow the limitations of implied warranties, or the exclusion ofincidental or consequential damages, so the above limitations and exclusions may not apply to you.Warranty service can be performed only by a Power Gear authorized service facility. This warranty willnot apply to service at any other facility. At the time of requesting warranty service, evidence of originalpurchase date must be presented.Power Gear950 Green Valley RoadP.O. Box 695Beaver Dam, WI 53916­06957