MLX90615

More documents

Recommendations

Info

MLX90615Infra Red Thermometer12 Application CommentsSignificant contamination at the optical input side (sensor filter) might cause unknown additionalfiltering/distortion of the optical signal and therefore result in unspecified errors.IR sensors are inherently susceptible to errors caused by thermal gradients. There are physical reasons forthat phenomena and, in spite of the careful design of the MLX90615, it is recommended not to subject theMLX90615 to heat transfer and especially transient conditions.Upon power-up the MLX90615 passes embedded checking and calibration routines. During these routinesthe output is not defined and it is recommended to wait for the specified POR time before reading the module.Very slow power-up may cause the embedded POR circuitry trigger on inappropriate levels, resulting inunspecified operation and is not recommended.The MLX90615 is designed and calibrated to operate as a non contact thermometer in settled conditions.Using the module in very different way will result in unknown results.Capacitive loading on a SMBus can degrade the communication. Some improvement is possible with useof current sources compared to resistors in pull-up circuitry. Further improvement is possible with specializedcommercially available bus accelerators. With the MLX90615 additional improvement is possible withincreasing the pull-up current (decreasing the pull-up resistor values). Input levels for SMBus compatiblemode have higher overall tolerance than the SMBus specification, but the output low level is rather low evenwith the high-power SMBus specification for pull-up currents. Another option might be to go for a slowercommunication (clock speed), as the MLX90615 implements Schmidt triggers on it’s inputs in SMBuscompatible mode and is therefore not really sensitive to rise time of the bus (it is more likely the rise time tobe an issue than the fall time, as far as the SMBus systems are open drain with pull-up).For ESD protection there are clamp diodes between the Vss and Vdd and each of the other pins. Thismeans that the MLX90615 might draw current from a bus in case the SCL and/or SDA is connected and theVdd is lower than the bus pull-ups’ voltage.It is possible to use the MLX90615 in applications, powered directly from the AC line (trasformerless). In suchcases it is very important not to forget that the metal package of the sensor is not isolated and thereforemay occur to be connected to that line, too. Melexis can not be responsible for any application like this andhighly recommends not to use the MLX90615 in that way.Check www.melexis.com for most current application notes about MLX90615.3901090615 Page 24 of 30 Data SheetRev 00128/Aug/2008
MLX90615Infra Red Thermometer13 Standard information regarding manufacturability of Melexisproducts with different soldering processesOur products are classified and qualified regarding soldering technology, solderability and moisture sensitivitylevel according to following test methods:Reflow Soldering SMD’s (Surface Mount Devices)• IPC/JEDEC J-STD-020Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices(classification reflow profiles according to table 5-2)• EIA/JEDEC JESD22-A113Preconditioning of Nonhermetic Surface Mount Devices Prior to Reliability Testing(reflow profiles according to table 2)Wave Soldering SMD’s (Surface Mount Devices) and THD’s (Through Hole Devices)• EN60749-20Resistance of plastic- encapsulated SMD’s to combined effect of moisture and soldering heat• EIA/JEDEC JESD22-B106 and EN60749-15Resistance to soldering temperature for through-hole mounted devicesIron Soldering THD’s (Through Hole Devices)• EN60749-15Resistance to soldering temperature for through-hole mounted devicesSolderability SMD’s (Surface Mount Devices) and THD’s (Through Hole Devices)• EIA/JEDEC JESD22-B102 and EN60749-21SolderabilityFor all soldering technologies deviating from above mentioned standard conditions (regarding peaktemperature, temperature gradient, temperature profile etc) additional classification and qualification testshave to be agreed upon with Melexis.The application of Wave Soldering for SMD’s is allowed only after consulting Melexis regarding assurance ofadhesive strength between device and board.Melexis is contributing to global environmental conservation by promoting lead free solutions. For moreinformation on qualifications of RoHS compliant products (RoHS = European directive on the Restriction Ofthe use of certain Hazardous Substances) please visit the quality page on our website:http://www.melexis.com/quality.aspThe MLX90615 is RoHS compliant3901090615 Page 25 of 30 Data SheetRev 00128/Aug/2008
Page 1 and 2: MLX90615Infra Red ThermometerFeatur
Page 3 and 4: MLX90615Infra Red Thermometer3 Tabl
Page 5 and 6: MLX90615Infra Red Thermometer6 Pin
Page 7 and 8: MLX90615Infra Red ThermometerParame
Page 9 and 10: MLX90615Infra Red Thermometer8.3.2
Page 11 and 12: MLX90615Infra Red ThermometerSpecia
Page 13 and 14: MLX90615Infra Red Thermometer8.4.3.
Page 15 and 16: MLX90615Infra Red ThermometerFigure
Page 17 and 18: MLX90615Infra Red Thermometer8.6 PW
Page 19 and 20: MLX90615Infra Red Thermometer8.7 Pr
Page 21 and 22: MLX90615Infra Red ThermometerTo, o
Page 23: MLX90615Infra Red Thermometer11.3 P
Page 27 and 28: MLX90615Infra Red ThermometerWhen a
Page 29 and 30: MLX90615Infra Red Thermometer17 Ref

MLX90615

Create successful ePaper yourself

Delete template?

Save as template?