read and save these instructions - Emerson Fans

More documents

Recommendations

Info

BP7407 44" & 52" Curva Sky 1/11/10 9:54 PM Page 8Check to see that all connections aretight, including ground, and that no barewire is visible at the wire connectors,except for the ground wire. Do notoperate fan until blades are in place.Noise and fan damage could result.ANTENNAWIREFigure 9WHITERECEIVERWIREBLACK RECEIVERWIREBLACK/WHITERECEIVER WIREFigure 10WHITE FAN WIRE! WARNINGBLACK FAN WIRESUPPLY & CEILING MOUNTINGPLATE GREEN WIRESSUPPLY,RECEIVER & FANWHITE WIRESSUPPLYBLACK WIRERECEIVERBLACK/WHITEWIREFAN &RECEIVERBLUE WIRESFAN BLACKWIRERECEIVERBLACK SUPPLYWIRERECEIVER BLACKWIRERECEIVERWHITESUPPLYWIREBLUE RECEIVERWIREBLUE FAN WIRE3. After connections have been made,turn leads upward and carefully pushleads into the outlet box, with the whiteand green leads on one side of theoutlet box and the black and blue leadson the other inside of the outlet box.! WARNINGTo avoid possible fire or shock, makesure that the electrical wires arecompletely inside the outlet box andnot pinched between the ceilingmounting plate and the fan motorhousing assembly.4. Remove one of the four screws in theceiling mounting plate and loosen theremaining three screws (Figure 11).5. Unhook the fan motor housing from theceiling mounting plate hook and lift thefan motor housing assembly up to theceiling mounting plate. Align andengage the motor assembly slots withthe three screw heads previouslyloosened by rotating the fan motorhousing assembly clockwise. Install thepreviously removed M5 x 10mm screwand secure the assembly to the plate(Figure 11). Completely tighten all fourscrews.Figure 11CEILINGMOUNTING PLATEM5 x 10mm PANHEAD CEILINGCOVER SCREWSFAN MOTORHOUSINGASSEMBLY6. Position the ceiling trim ring over eachof the protruding ceiling cover screwheads and rotate the ceiling trim ringclockwise to secure (Figure 12).CEILING COVER SCREWHEADS (4)CEILINGTRIM RINGFAN MOTORHOUSINGASSEMBLYFigure 128UL Model No.: CF144 & CF152
BP7407 44" & 52" Curva Sky 1/11/10 9:54 PM Page 9How to Assemble YourLight Kit Glass Shade1. Screw in two 50-watt (maximum)halogen mini candelabra base bulbs inthe light kit plate sockets (Figure 13).50-WATT (maximum)HALOGEN MINICANDELABRA BASEBULBS (2)Figure 13LIGHT KIT PLATESOCKETS (2)2. Place the glass shade into the openingin the fan motor housing assembly,aligning the three flat areas on the topedge of the glass with the three raiseddimples on the fan motor housingassembly and turn the glass shadeclockwise until it stops (Figure 14).NOTE: periodically check that the glassshade is seated fully clockwise in thefan motor housing assembly.How to Assemble YourNo Light Cover Plate! WARNINGDo not install any light bulbs into thelight kit plate if using the cover plate.Installation of light bulbs when usingthe cover plate could result in fire,shock and serious personal injury.1. Place the cover plate onto the lowerhousing aligning the three flat areas onthe top flange of the cover plate withthe three pins on the inside of the fanmotor housing assembly (Figure 15).Then turn the cover plate clockwiseuntil it stops turning.2. Your cover plate is now installedDO NOT INSTALL LIGHT BULBSWHEN USING THE COVER PLATEDIMPLES (3)FLAT AREA (3)COVERPLATEFigure 15DIMPLES (3)FLAT AREA (3)GLASSBOWLFigure 149UL Model No.: CF144 & CF152
Page 1 and 2: BP7407 44" & 52" Curva Sky 1/11/10
Page 7: BP7407 44" & 52" Curva Sky 1/11/10

read and save these instructions - Emerson Fans

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?