Infinity Operations Manual (96402,96403, 96406, 96407) - Whip Mix

More documents

Recommendations

Info

ERROR CODESNOTE: “Beeps” occur when the Error Code appears on the Main Displayerrorcode DESCRIPTION PROBABLE CAUSEEr 1Er 2INVALID ENTRYERROR: STAGE,HEAT RATE andTEMP lights flashTABLETTEMPERATURECALIBRATIONERROROccurs when the HEAT RATE is set to COOL but the TEMP of that stage ishigher than the TEMP of the prior stage (should be heating). This will occurwhen a program is already running and a parameter was edited in process.Occurs when the temperature on the display is outside the allowable rangeat the time the user pressed the ENTER / REVIEW keys simultaneously to setthe <strong>Infinity</strong> calibration temperature to 1500°F. If this occurs and is not anoperator error, it indicates that there is a problem with the thermocouple orthe PC board. Press ENTER / REVIEW to turn off the error indication andcontinue with the program. Press START / STOP to end the program.Er 3ELECTRONICSMALFUNCTIONOccurs when PC board hardware malfunctions.Er 4OPENTHERMOCOUPLEOccurs if the thermocouple is open or the connecting wire(s) are broken ordisconnected from the terminal board.Er 5REVERSEDTHERMOCOUPLEORNO HEATOccurs if the thermocouple extension wires have been connected backwardsto the terminals on the printed circuit board. The error will be detected 5minutes after heating program started. This error will also occur if theprogram is started and the chamber door is kept open for 5 minutes or therelay is defective, the heater plates are defective or there is a problem withthe main PC board.17
ERROR CODESerrorcode DESCRIPTION PROBABLE CAUSEEr 6Er 7SHORTEDTHERMOCOUPLE ORDEFECTIVE HEATERPLATESTHERMALRUNAWAYOccurs if the thermocouple wires are shorted or the heater plates aredefective causing <strong>Infinity</strong> to achieve a HEAT RATE of less than 6% of themaximum attainable HEAT RATE with full power applied to the heaterplates for 5 minutes. This error will also occur if a program is runningand the door is kept open for more than 5 minutes or the relay or theMain PC board developed a problem during a burnout process.Occurs when the temperature has exceeded 2015°F (1102°C) for 1minute if the highest temperature programmed was less than 2000°F(1093°C). This also occurs when the temperature has exceeded 2050°F(1121°C) for 1 minute if the highest temperature programmed was2000°F (1093°C) or higher.Flashing99:99 whenNIGHT / TIMESET (DELAYSTART) ispressedduring aprograminvalid entryerror while aprogram isrunningOccurs when the HEAT RATE in STAGE 2, 3 or 4 is set to “COOL” butthe corresponding TEMP is entered to heat to a higher temperaturethan the previous stage.18
Page 2 and 3: TABLE OF CONTENTSIntroduction .....
Page 4 and 5: SPECIFICATIONSINFINITY MElectrical
Page 6 and 7: PROGRAMkey parts identification and
Page 8 and 9: installationunpack and set-up1. Unp
Page 11 and 12: operationprogram and operate - TWO
Page 13 and 14: operationprogram and operate - four
Page 15 and 16: OPERATIONedit while a program is ru
Page 17: OPERATIONSample three stage program
Page 21 and 22: SERVICE6. When the tablet begins to
Page 23 and 24: Figure 4INFINITY WITH UPPER REAR PA
Page 25 and 26: Figure 5INFINITY WIRING DIAGRAM24
Page 27 and 28: FIELD SERVICEREPLACEMENT OF THE SSR
Page 29 and 30: SPARE PARTS LISTSPARE PARTS FOR INF
Page 31 and 32: PROGRAM CARD FORMSProgram #Metal(s)

Infinity Operations Manual (96402,96403, 96406, 96407) - Whip Mix

Create successful ePaper yourself

Delete template?

Save as template?