MTR-40F REV 0.p65 - Southern Tool

More documents

Recommendations

Info

MTR-40F— MAINTENANCE (RAMMER/ENGINE)Crankcase Lubrication■ The rammer crankcase bearings (Figure 19) should belubricated with five shots of grease with a hand grease gunafter each eight (8) hours of use.■ Use MQ HIGH TEMPERATURE GREASE, P/N GRS2 or itsequivalent.Spark Plug■ Remove and clean the spark plug (Figure 20), then adjustthe spark gap to 0.024 ~0.028 inch (0.6~0.7 mm). This unithas electronic ignition, which requires no adjustments.Figure 20. Spark Plug GapFigure 19. Grease Fittings (Crankcase)Fuel Lines■ Check the fuel and oil lines regularly for damage and ensurethat there are no leaks.■ Replace the fuel lines every two years to maintain theperformance and flexibility of the fuel lines.Cleaning the Rammer■ If using a high pressure spray washer, be careful not to splashwater directly on the air cleaner, carburetor, muffler, and fuelcap. Excessive amounts of water may cause severe enginedamage.Long Term Storage■ Drain fuel from fuel tank, fuel line and carburetor.■ Remove spark plug and pour a few drops of motor oil intocylinder. Crank engine 3 to 4 times so that oil reaches allinternal parts.■ Clean exterior of rammer with an oil-moistened cloth.■ Store unit covered with plastic sheet in moisture free anddust free location out of direct sunlightNOTEReference manufacturer enginemanual for specific servicinginstructions.PAGE 20 — MTR-40F— PARTS & OPERATION MANUAL — REV. #0 (01/21/04)
Perform the scheduled engine maintenance procedures asdefinded by Table 4 below:MTR-40F — MAINTENANCE (ENGINE)Table4. EngineMaintenanceScheduleDESCRIPTION(3)OPERATIONBEFOREFIRSTMONTHOR10 HRS.EVERY3 MONTHSOR25 HRS.EVERY6 MONTHSOR50 HRS.EVERYYEAROR100 HRS.EVERY2 YEARSOR200 HRS.Engine OilCHECKCHANGEXXAir CleanerCHECKXC HANGEX (1)All Nuts & BoltsRe-tighten IfNecessaryXSpark PlugCHECK-CLEANREPLACEXXCoolingFinsCHECKXSparkFuelFuelArresterTankFilterCLEANCLEANCHECKXXXIdleValveFuelSpeedClearancelinesC HECK-ADJUSTX (2)C HECK-ADJUSTX (2)C HECKEvery 2 years (replace if necessary) (2)( 1) Service more frequently when used in D USTYareas.(2) These items should be serviced by your servic dealer, unless you have the proper tools and are mechanicallyproficient. Refer to the ROBIN shop Manual for service procedures(3) For commercial use, log hours of operation to determine proper maintenance intervals.MTR-40F— PARTS & OPERATION MANUAL — REV. #0 (01/21/04) — PAGE 21
Page 1 and 2: OPERATION AND PARTS MANUALTamping R
Page 3 and 4: HERE'S HOW TO GET HELPPLEASE HAVE T
Page 5 and 6: When ordering parts,please supply t
Page 7 and 8: MTR40-HS — SAFETY MESSAGE ALERT S
Page 10 and 11: MTR-40F — OPERATION AND SAFETY DE
Page 12 and 13: MTR-40F — SPECIFICATIONSTable1.MT
Page 14 and 15: MTR-40F — BASIC ENGINEFigure 2. E
Page 16 and 17: MTR-40F— PRE-INSPECTION/INITIAL S
Page 18 and 19: MTR-40F— OPERATIONOperation1. To
Page 22 and 23: MTR-40F— TROUBLESHOOTING GUIDETAB
Page 24 and 25: How to read the marks and remarks u
Page 26 and 27: MTR-40F— NAMEPLATE AND DECALSNAME
Page 28 and 29: MTR-40F— CRANKCASE AND ENGINE ASS
Page 30 and 31: MTR-40F— CRANKCASE AND ENGINE ASS
Page 32 and 33: MTR-40F — GUIDE CYLINDER ASSY.GUI
Page 34 and 35: MTR-40F— TANK AND HANDLE ASSY.TAN
Page 36 and 37: MTR-40F— FOOT ASSY. (OPTION)FOOT
Page 38 and 39: MTR-40F— NARROW FOOT ASSY. (OPTIO
Page 40 and 41: MTR-40F— TRENCH SHOE ASSY. (OPTIO
Page 42 and 43: ROBIN EH-09 ENGINE — CRANKCASE AS
Page 44 and 45: CRANKSHAFT AND PISTON ASSY.ROBIN EH
Page 46 and 47: INTAKE AND EXHAUST ASSY.ROBIN EH-09
Page 48 and 49: ROBIN EH-09 ENGINE —GOVERNOR ASSY
Page 50 and 51: ROBIN EH-09 ENGINE —BLOWER HOUSIN
Page 52 and 53: ROBIN EH-09 ENGINE — CARBURETOR A
Page 54 and 55: ROBIN EH-09 ENGINE —ELECTRIC DEVI
Page 56 and 57: Effective: October 1, 2002TERMS AND
Page 58: OPERATION AND PARTS MANUALHERE'S HO

MTR-40F REV 0.p65 - Southern Tool

Create successful ePaper yourself

Delete template?

Save as template?