Washer-disinfector G 7882 CD

More documents

Recommendations

Info

PlumbingConnection to the water inlet,The water in the machine mustnot be used as drinking water.– The machine must be connected tothe water supply in strict accordancewith current local and national waterauthority regulations (WRC in theU.K.).– If the iron content in the water is toohigh, there is a risk of corrosiondamage to instruments.If the chloride content of the waterexceeds 100mg/l, the risk ofcorrosion damage to instruments willincrease considerably.– If there are too many impurities in thelocal water supply, it will benecessary to operate the steamcondenser with de-mineralisedwater.– This machine is constructed tocomply with German waterregulations (DVGW), and may beconnected to a suitable supplywithout an extra non-return valve ifnational regulations permit.– The minimum flow pressure for acold water connection is 100 kPa(1.0 bar) and with an AD waterconnection it is 60 kPa (0.6 bar).– The recommended flow pressurefor a cold water connection is0 250 kPa (2.5 bar) and for an ADwater connection is 0 150 kPa (1.5bar). Otherwise fill times will be toolong.– The maximum permitted staticwater pressure is 1000 kPa (10 bar).– If the water pressure is not in therange specified above (the p / 6indicator light may come on and thefault code F E will appear in thedisplay) please contact the MieleService Department for advice.– This machine is supplied as standardfor connection to a cold watersupply. The inlet hose must only beconnected to the cold waterstopcock.– The inlet hose for the steamcondensor (without non-return valve)must only be connected to the coldwater stopcock.– AD water connection - see thefollowing page.– A stopcock with 3/4 inch male threadmust be provided on site. It shouldbe easily accessible so that thewater supply can be turned off whenthe machine is not in use.– The DN 10 inlet hose is approx.1.7 m long terminating in a 3/4 inchfemale thread. On no account mustthe inlet filter be removed.– Large surface area filters areenclosed in the kit supplied with themachine for installing between thestopcock and the inlet hose (seeillustration in "Maintenance -Cleaning the filters in the washcabinet'"). The large surface areafilter for the AD water supply is madefrom chrome nickel steel, and can berecognised by the matt top surface.76
Plumbing,The inlet hose must not beshortened or damaged in any way(see illustration).See also the installation diagramsupplied.AD water connection ö 0.6 - 10 bar(60 - 1000 kPa) over pressureThe machine is supplied as standardfor connection to an AD water supply of0.6 - 10 bar (60 - 1000 kPa). If the waterpressure (flow rate) is below 1.5 bar(150 kPa) the water intake time isautomatically extended.^ The AD pressure tested hose(marked "H 2 O pur") with a 3/4"threaded union must be connected tothe on-site AD stopcock for purifiedwater.If the AD water supply is not used,the electronics must bere-programmed by a Mieleapproved service technician. Theinlet hose will remain on the rear ofthe machine.77
Page 1 and 2:
Operating instructionsWasher-disinf
Page 3 and 4:
ContentsAdding cleaning agent .....
Page 5 and 6:
Warning and Safety instructionsThis
Page 7 and 8:
Warning and Safety instructionsThe
Page 9 and 10:
Warning and Safety instructionsUsin
Page 11 and 12:
Description of the machineThe clean
Page 13 and 14:
Guide to the machinea Drying unit (
Page 15 and 16:
Opening and closing the doorElectri
Page 17 and 18:
Water softenerTable of settings°d
Page 19 and 20:
Water softenerAdd salt indicatorRea
Page 21 and 22:
Areas of applicationLoading the mac
Page 23 and 24:
Areas of application(OP) Surgical i
Page 26 and 27: Areas of application,To minimise th
Page 28 and 29: Areas of applicationOphthalmologyTh
Page 30 and 31: Dispensing chemical agentsAdding ri
Page 32 and 33: Dispensing chemical agentsAdding ne
Page 34 and 35: Dispensing chemical agentsAdding ch
Page 36 and 37: Dispensing chemical agentsAdd liqui
Page 38 and 39: OperationSwitching on^ Close the do
Page 40 and 41: OperationAdditional dryingIf additi
Page 42 and 43: Programmable functionsDispensing li
Page 44 and 45: Programmable functionsDispensing ch
Page 46 and 47: Programmable functionsChanging prog
Page 48 and 49: Programmable functionsResetting to
Page 50 and 51: Programmable functionsResetting the
Page 52 and 53: MaintenancePeriodic checksThis wash
Page 54 and 55: MaintenanceCleaning the filters in
Page 56 and 57: MaintenanceCleaning the spray armsT
Page 58 and 59: MaintenanceBaskets and insertsBaske
Page 60 and 61: MaintenanceChanging the fine filter
Page 62 and 63: Problem solving guideFault Possible
Page 70 and 71: Other problemsCleaning the drain pu
Page 72 and 73: After sales serviceIn the event of
Page 74 and 75: InstallationLevel and secure the ma
Page 78 and 79: PlumbingDrainage- The drainage syst
Page 80 and 81: Programme chartProgrammeWhen to use
Page 84: Alteration rights reserved / 3807 M
show all

Washer-disinfector G 7882 CD

Create successful ePaper yourself

Delete template?

Save as template?