Tech Sheet for Miscellaneous Controls (VF5602-42AA-NEW)

More documents

Recommendations

Info

No Purge ModelsFigure 5.1 No Purge and Purge Wiring DiagramsPurge Models5602/5605:120 VAC50/60 HZ5603:240 VAC50/60 HZ5602/5605:120 VAC50/60 HZ5603:240 VAC50/60 HZ15 AFuseOn/Off12Piloted Burner15 AFuseOn/Off12Piloted Burner3Pilot3PilotInterlocks & Limits457IgnitionMainAir Flow Switch456IgnitionMainProof ofClosureAVS1S2AlarmInterlocks& LimitsProof of Closure78AVFanAlarmS1GS2GFigure 5.2 Modulation Wiring Diagram5602/5605:120 VAC50/60 HZ5603:240 VAC50/60 HZ15 A. FuseOn/Off1Air FlowCut RedJumperTo ActivateTerminal D.2345Low Fire ProvingPilotIgnitionMain6Interlocks& Limits78FanProof ofClosureHigh PurgeDamperSwitchADS2S110111213FlameSensorTerminalsCommonAutomaticLow FireHigh FireAlarmSee the “High toLow Fire PurgeModulationCapability” sectionon page 16 forcontact connections.G20Eclipse Veri-Flame Instruction Manual 818-6/06
Figure 5.3 Typical Connections For All Models21S1S2Self Check U.V. 5602-91(Requires 5602-91-7 cable)ABCDModel 5602 DBP120 VAC Remote Display12V+12V-Tx Rx120V 120VN LCable#20318to 120 VACR1R2GPLUGTo 1Flame SignalTest JackTo S2Veri-Flame21S1S2Self-Check U.V. 5602-91(Requires 5602-91-7 cable)for 240 VAC Veri-Flame240VT1120VABCDSolid State U.V. / I.R.WhiteS1BlackScannerS2G ShieldS1S2BlueFlame RodFlame RodT1Third party transformer required. Must be at least 25 VA.S1S2U.V.Blue (Signal)Yellow (Neutral)U.VorI.R.No Purge & PurgeDirect Spark345MAINIGNITIONNote: Intermittent pilot mustbe selected, DIP-SW2 = ONNeutral345ModulationDirect Spark withLow Fire StartLow Fire ProvingCRCRMAINIGNITIONNeutralNote: Intermittent pilot must be selected, DIP-SW2 = ONCR is a control relay used to bypass the low fire switch afterthe burner is lit.Notes for Figures 5.1, 5.2 & 5.3:1. Ground, shielding and conduit must not be connected to terminal S2.2. Control circuit wires must meet 90°C (194°F) specification minimum and mustbe No. 16 AWG or larger and in accordance with all applicable codes.3. Flame sensor wires must be individually run in their own separate conduit; flamesensor wires CANNOT be run together in a common conduit or wireway (SeeSection 6).4. Flame signal should read between 4 and 10 VDC with a digital volt meter. Drop offis approximately 4.0 VDC. Positive test jack point is on the cover marked “FlameSignal” with negative point being the S2 or ground.5. Purge time, TFI, intermittent/interrupted pilot, and recycle/non-recycle selectionsare made with a DIP switch located on the rear plate of the control unit.6. Neutral must be grounded.Eclipse Veri-Flame Instruction Manual 818-6/0621
Page 1 and 2: Instruction Manual 8186/1/06Veri-Fl
Page 3 and 4: About this manualAudienceScopeDocum
Page 5 and 6: Table of ContentsAbout this manual
Page 7 and 8: 89Maintenance & Troubleshooting ...
Page 9 and 10: Specifications2IntroductionSpecific
Page 11 and 12: Dimensions (continued)Veri-Flame/Mo
Page 14 and 15: Function Summary4IntroductionStanda
Page 16 and 17: System Errors &Lockout Conditions(C
Page 18 and 19: System Installation5IntroductionIn
Page 22 and 23: Figure 5.4 Purge and No Purge Bases
Page 24 and 25: Sensor Installation6IntroductionThi
Page 26 and 27: Test Procedures7IntroductionThis se
Page 28 and 29: Maintenance & Troubleshoot-8Introdu
Page 30 and 31: LED StatusThis section describes th
Page 32 and 33: Table 8.3 LED Status & Conditions f
Page 34 and 35: Table 9.1 Veri-Flame Operating Sequ
Page 36 and 37: Table 9.1 Veri-Flame Operating Sequ
Page 38 and 39: Table 9.2 Remote Display Diagnostic
Page 40 and 41: Table 9.2 Remote Display Diagnostic
Page 42 and 43: Illustrated PartsList12CategorySens

Tech Sheet for Miscellaneous Controls (VF5602-42AA-NEW)

Create successful ePaper yourself

Delete template?

Save as template?