Palax KS35 Ergo/S Manual - Hakmet

More documents

Recommendations

Info

206 How the safety devices affect the operation of the machine, all models6.1 Protective net for splitting chute A, Fig. 25 The protective net must always be closed whenworking with the machine. The chain-saw does not operate, if the net isopen. The splitting cylinder does not operate, if thenet is open. If the net is opened while the splitting operationis in progress, the splitting movement will stopand the cylinder will return to its initial position.25BA6.2 Active wood clamp B, Fig. 25 The spring-loaded or hydraulic log-clamp, Fig. 25, 26 and 27, is an easy-to-operatedevice that prevents the log from moving during cutting. The grooved roller of the log-clamp efficiently prevents the log from turning duringcutting. Long and straight trees stay in position on the deck by virtue of their ownweight during cutting. Short and slender trees require the use of log-clamp because tha saw-chain easily"bites" in small and light trees and thus causes a dangerous situation.As necessary, the pressing force can be increased using the lever B.6.3 Spring-loaded log-clamp, Fig. 26 Standard equipment in Ergo model. The spring A keeps the clamp tight against thelog at all times.A B The pressing force can be increased for shortor lightweight trees using the hand lever B forthe clamp.6.4 Log-clamp with hydraulic cylinder, Fig. 27 26C Standard equipment in S model As the crosscut movement is launched, the log-clamp C immediately presses the treeagainst the infeed conveyor and prevents it from moving during cutting. As the crosscut saw-bar comes up, thepressure is relieved from the log-clamp cylinderand the tree can be fed against the log-stop forCthe next cutting pass.The active log-clamp improves safety andreduces malfunctions.27Warning !All the safety-related devices are necessary to ensure a sufficient level of afety.Do not remove any of the safety features from the machine. The machine operator isresponsible for the flawless operation of the safety-related devices.Palax_KS_35_Ergo+S_v4_07_EN.doc
7 Operation of cutting, splitting and the infeed conveyor, Ergo model7.1 Denomination of parts, Ergo model, Fig. 281. Splitting valve2 Hand-start lever3 Launch bar4 Spring5 Launch bar6 Launch device7 Spring8 Oil pump lever9 Valve for saw-motorand infeed conveyor10 Multi-purpose shaft11 Back stop12 Launch bar1 2 3 4 5 6 7 8 9 10 11 12287.2 Operating principle of cutting, splitting and the infeed conveyor, Ergo model217.3 CuttingPull the multi-purpose lever A in direction B, Fig. 29 Multi-purpose shaft 10, Fig. 28, swings to the rear and thelaunch rod swing with it. The cam 7 of the multi-purpose shaft presses the oil pump lever8, which applies oil to the saw-bar.A7.4 Splitting Push the multi-purpose lever A in direction C, Fig. 29C The launch rod 6 on the multi-purpose shaft 10 presses theBlaunch lever 5. This makes the spring-loaded launch rod 3activate the splitting valve 1. The splitting cylinder executes one stroke and then returns to its29initial position. The chain-saw will stop as soon as the multi-purpose lever A comes in contact with thespring-loaded limiter in the front.7.5 Feeding the tree Push the multi-purpose lever A in direction C against the spring-loaded limiter. Multi-purpose shaft 10 activates the valve 9 and the infeed conveyor transfers the treeagainst the log-stop.7.6 Hand-start and stopping of the splitting operation The splitting operation can also be started using the hand-start lever 2 by pushing thelever to the right. The hand-start lever starts the splitting operation by directly actuating the splitting valve1 by means of the launch rod 3, Fig. 28. The splitting operation can also be stopped using the hand-start lever.Palax_KS_35_Ergo+S_v4_07_EN.doc
Page 2 and 3: Palax_KS_35_Ergo+S_v4_07_EN.doc2
Page 4 and 5: 46 HOW THE SAFETY DEVICES AFFECT TH
Page 6 and 7: 1.2 Intended use of the machineThis
Page 8 and 9: 1.9 Machine models8All models come
Page 10 and 11: 2.5 Main parts, Fig. 6, all models1
Page 12 and 13: 3.2 Operating the Palax 35 Ergo mod
Page 14 and 15: 3.7 Infeed conveyor, Fig. 14 and 15
Page 16 and 17: 163.12 Heater carpet for hydraulic
Page 18 and 19: 5.2 High-speed valve with automatic
Page 22 and 23: 8 Operation of cutting, splitting a
Page 24 and 25: 9.5 Changing the hydraulic oil and
Page 26 and 27: 9.13 Changing the saw-chain, Fig. 4
Page 28 and 29: 10 Maintenance schedule28Object Tas
Page 30 and 31: Palax_KS_35_Ergo+S_v4_07_EN.doc30

Palax KS35 Ergo/S Manual - Hakmet

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?