Palax KS35 Ergo/S Manual - Hakmet

More documents

Recommendations

Info

10 Maintenance schedule28Object Task Daily Serviceinterval100 tGearboxTR-drivenHydraulic oilNormal conditionsCheck1 Change2 ChangeCheck1 Change2 ChangeXXServiceinterval500 hXXServiceinterval1000 hXXMaterial /MethodSAE 80 0.5 lSuction drainageVolume 55 le.g. Esso Univis 32Neste Hydrauli 32F 10 100/3Oil filter1 ChangeX2 ChangeXValve Lubrication X Lubrication oil, sprayAll levers Lubrication X Lubrication oil, sprayConveyor bearing Lubrication X VaselineConveyor chain Lubrication X Lubrication oil, sprayCrosscut saw-blade SharpeningChangeAsrequiredSawbar Change AsrequiredMachine Cleaning XElectric motor Cleaning XCombustion engine Service X Instruction manual ofengineElectric equipment Cleaning X11 Malfunctions and their remedyDisturbance Cause RemedyThe saw-chain is heavy onpower and gets hot.1. The chain is blunt. 1. Sharpen or replace thechainOblique resulting surface 1. The other side of thechain is blunt, e.g. after. Sharpen or replace thechainsawing through a nailSplitting is not operational 1. Protective net open . Close the protective netSaw-bar does not come 1. Protective net open 1. Close the protective netdownSplitting cannot be launched 1. Wrong adjustment of the 1. Adjustlaunch rodThe splitting motion starts 1. The valve does not lock . Undo rear stopper for thethen stopsThe cylinder is movingerratically and jamsThe conveyor does not startupThe machine equipped withhigh-speed valves onlyoperates at one speeduplaunch rod about 1 turn1. Malfunction of valve 1. Lubricate the detent endof the valve2. Lubricate the spool shifter1. Scrapers frozen to thebed2. Pressure too low3. Debris between thescraper and the edge1. Debris in the high-speedvalve1. Lift the chain2. Raise the pressure, screwthe relief valve up about½ a turn3. Remove the debris1. Open and clean the valvePalax_KS_35_Ergo+S_v4_07_EN.doc
12 Electric diagrams29Palax_KS_35_Ergo+S_v4_07_EN.doc
Page 2 and 3: Palax_KS_35_Ergo+S_v4_07_EN.doc2
Page 4 and 5: 46 HOW THE SAFETY DEVICES AFFECT TH
Page 6 and 7: 1.2 Intended use of the machineThis
Page 8 and 9: 1.9 Machine models8All models come
Page 10 and 11: 2.5 Main parts, Fig. 6, all models1
Page 12 and 13: 3.2 Operating the Palax 35 Ergo mod
Page 14 and 15: 3.7 Infeed conveyor, Fig. 14 and 15
Page 16 and 17: 163.12 Heater carpet for hydraulic
Page 18 and 19: 5.2 High-speed valve with automatic
Page 20 and 21: 206 How the safety devices affect t
Page 22 and 23: 8 Operation of cutting, splitting a
Page 24 and 25: 9.5 Changing the hydraulic oil and
Page 26 and 27: 9.13 Changing the saw-chain, Fig. 4
Page 30 and 31: Palax_KS_35_Ergo+S_v4_07_EN.doc30

Palax KS35 Ergo/S Manual - Hakmet

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?