Palax KS35 Ergo/S Manual - Hakmet

More documents

Recommendations

Info

9.5 Changing the hydraulic oil and the filter, Fig. 35 The oil plug C is located in the bottom of the tank. The filter A must also be replaced, because contaminantsthat end up in the filter are constantly extracted from thesystem. The volume required for oil-change is about 55 litres. Leave an expansion space of about 5 cm in the upper partof the tank.24A BC9.6 Servicing the valve, Fig. 3635To withstand and operate flawlessly, thedetent end A, the spool shifter joint B and theball joint of the control valve require regularlubrication.Lubrication of the valve is particularlyimportant if the machine is to be left standingfor several months. If the parts of the detenthave become rusty, the machine will notoperate flawlessly.9.7 Detent end of the valve, Fig. 3736ABThere is a small hole in the middle of the end plate of thedetent end of the valve for spraying lubricant onto the movingparts of the valve detent.Only use oil that does not congeal in frost.The easiest way is to use a spray bottle with a nozzle andpipe.A Insert the spray pipe in the hole A and press 2-3 times forabout 1 second at a time. The oil spreads smoothly on the moving parts of thedetent end.37NOTEDo not use spray Vaseline because it congeals in severe frost and thevalve will not operate properly.9.8 Lubricating the spool shifter, Fig. 38The spool shifter is equipped with a pin and a ball joint thatrequire regular maintenance and lubrication.Lift up the edge of the protective rubber of the spoolshifter.Spray lubricant on both sides of the pin and on the balljoint.At the same time, check that the rubber is intact.38Palax_KS_35_Ergo+S_v4_07_EN.doc
9.9 Structure of the detent end and the correct order of parts, Fig. 3925Keep cover C of the detent end depressed while opening screws B, as the stiff springs canthrow the cover off. This can also make the springs and balls of the detent fly off.In connection with assembly of the detent end, apply a small amount of Vaseline to holesA of the detent. This ensures the balls stay properly in position during assembly. Makesure that parts D and E line up in the right way, as shown in the picture, and that thecondensed-water drain holes always point downwards.CBD EF39A9.10 Initial settings of the valveThe valve has been adjusted and test run at the factory.The initial settings do not usually change so there is rarely any need for readjustment.9.11 Changing the saw-chainWARNING!Stop the machine before opening the crosscut saw housing.9.12 Opening the saw-bar cover, see point 9.2WARNING!The saw-chain is sharp: handle with gloves.Palax_KS_35_Ergo+S_v4_07_EN.doc
Page 2 and 3: Palax_KS_35_Ergo+S_v4_07_EN.doc2
Page 4 and 5: 46 HOW THE SAFETY DEVICES AFFECT TH
Page 6 and 7: 1.2 Intended use of the machineThis
Page 8 and 9: 1.9 Machine models8All models come
Page 10 and 11: 2.5 Main parts, Fig. 6, all models1
Page 12 and 13: 3.2 Operating the Palax 35 Ergo mod
Page 14 and 15: 3.7 Infeed conveyor, Fig. 14 and 15
Page 16 and 17: 163.12 Heater carpet for hydraulic
Page 18 and 19: 5.2 High-speed valve with automatic
Page 20 and 21: 206 How the safety devices affect t
Page 22 and 23: 8 Operation of cutting, splitting a
Page 26 and 27: 9.13 Changing the saw-chain, Fig. 4
Page 28 and 29: 10 Maintenance schedule28Object Tas
Page 30 and 31: Palax_KS_35_Ergo+S_v4_07_EN.doc30

Palax KS35 Ergo/S Manual - Hakmet

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?