New micro size drive STARVERT - Bermar.it

More documents

Recommendations

Info

Parameter Descriptions▒ Program groupDisplayP33Function Setting range Description Factory default Mode changeduring runSetting the fault detect item as per user selection.The input/output phase loss, ground detect during run can be selected.User selection faultdetect0 ~ 7 [bit]User selectionfault detect [Trip]01234567Ground detectduring run GCtInput phase lossdetect CoLOutput phaseloss detect(Pot)bit 2 bit 1 bit 0-vvvv-vvvv-vvvv0P34Selecting start withpower input0 ~ 1P34 is only used in case the operation command method is selected.Either terminal number 1 or 2. Acceleration is getting startedwhen the FX or RX terminal is on with power input.0XP35Selecting start after trip0 ~ 1P34 is only used in case the operation command method is selectedeither terminal number 1 or 2.In the condition that the FX and RX terminals are on, aftertrip, resetting starts acceleration.0While motor is on spining, this function prevents the probable faults.Starting withpowerinput(P34)Restart afterinstant powerfailureOperation aftertrip (P35)GeneralAccelerationP36P37Speed search selectionSpeed searchcurrent level0 ~ 15 [bit]80 ~ 200 [%]bit 3 bit 2 bit 1 bit 00123456789101112131415--------vvvvvvvv----vvvv----vvvv--vv--vv--vv--vv-v-v-v-v-v-v-v-vThe current size during speed search operation is limited.Motor rated current(P43) is standard.0100P38Number of times ofAuto-restart0 ~ 10Setting number of times that drive can operate automaticallyafter trip.If trips exceed the set times, drive does not restart automatically. Onlyuse when the operation command method(drv) ofoperation group is selected either terminal umber 1 or 2and the operation command is inputted.However, the Auto-restart does not work in case the protectivefunctions such as OHT, LVT, EST and HWT are in active.0P39Auto re-start stand bytime after trip0 ~ 60 [sec]Re-start is operated after the auto re-start stand-bytime of trip.P40 Motor capacity selection 0.1 ~ 0.4- *Note2) XP41 Number of poles of motor 2 ~ 12Used for number of spining times of motor of the operation group.4X1.014 _*Note2) The initial value of P40 is set for the drive capacity.
New micro size driveSTARVERTParameter Descriptions▒ Program groupDisplayP42P43Motor ratingSlip frequencyMotor rated currentFunction Setting range Description Factory default Mode changeduring run0 ~ 10 [Hz]0.0 ~ 25.5 [A]The difference value between input power frequency and motor nameplate displayed rated spin times(rpm) is inputted.The printed rated current value of name plate is inputted.- *Note3)-XXP44Non-load current ofmotor0.0 ~ 25.5 [A]After taking out load from motor, the current value which was measuredin operation condition of rated spin times is inputted.-XP45Carrier frequency selection1 ~ 10 [kHz]As the set carrier value is larger the noise is smaller but the leakingcurrent is bigger.3P46P47P48P50P51P52Control typeselectionPI control P gainPI control I timePI control F gainPI frequencyhighest limitPI frequencylowest limit0 ~ 20 ~ 999.9 [%]0.1~32.0 [sec]0 ~ 99.99 [%]0.1 ~ 200 [Hz]0.1 ~ 200 [Hz]012V/F controlSlip compensation controlPI controlGain setting for PI control response.Feed forward of PI controlLimits the frequency size that comes from PI calculation.The setting value can be between the maximumfrequency(P16) and starting frequency(18).0300.01.00.060.05.0XFirst displayed items on the loader with power input.P53Power input displayselection0 ~ 15P54Gain of number of timesof motor1 ~ 1000 [%]P55 Constant number of AI filter input 0 ~ 9999P56 Minimum input of AI0 ~ 100 [%]P57AI input maximumvoltage matching0 ~ 200P58 AI maximum input0 ~ 100 [%]P59AI input maximumvoltage matching frequency0 ~ 200 [Hz]P60 Volume input filter constant 0 ~ 9999P61 Volume input minimum value 0 ~ 100 [%]P62Volume input maximum voltagematching frequency0 ~ 200 [Hz]P63 Volume input maximum value 0 ~ 100 [%]P64Volume input maximum voltagemachine frequency0 ~ 200 [Hz]Phase loss standardP65 selection of analog0 ~ 2speed command0 Operation frequency1 Acceleration time2 Deceleration time3 Operation command method4 Frequency command method5 Multi-step frequency 16 Multi-step frequency 27 Multi-step frequency 38 Output current (Cur)9 Number of times of motor spin(rpm)10 Drive DC voltage (DCL)11 User selection (vOL)12 Fault status 113 Operation direction selection14 Output current display15 Displaying number of times of motor spinBy calculating the gear rate of load system, displays the numberof times of motor. Monitoring is possible at the (rPM) code.Controlling the analog input response.Minimum analog input value can be set as % of total input.Analog input minimum case frequency.The maximum analog input value can be set as all input percent(%).The maximum frequency value of analog input.Response speed control of volume input operation.The volume input minimum spin value can be set as all input percent(%).Volume input minimum value frequency.The volume input maximum value can be set as all input percent(%).The volume input maximum value frequency.012No operationOperation below half value of setOperation below set value01001000.010060.01000.010060.00*Note3) All the values from P42 and P44 are modified to adopt the motor capacity P40.STARVERT iE5 _ 15
Page 1: www.lsis.comNew micro size driveof
Page 4 and 5: Slim and variety!Our iE5 is best fi
Page 6 and 7: Model and Specifications0.1kW(1/8HP
Page 8 and 9: Wiring*Note4)*Note1)*Note2)Analogue
Page 10 and 11: Shifts between each code and group
Page 12 and 13: Parameter Descriptions▒ Operation
Page 16 and 17: Parameter Descriptions▒ Program g
Page 18: ProtectionsDisplay Protections Desc
Page 21 and 22: New micro size driveSTARVERTDimensi
Page 23 and 24: New micro size driveSTARVERTMemoSTA

New micro size drive STARVERT - Bermar.it

Create successful ePaper yourself

Delete template?

Save as template?