Snapper Lawn Tractor Hydrostatic Drive Electric Clutch Series G ...

More documents

Recommendations

Info

Section 2 - OPERATING INSTRUCTIONS2.3 STARTING & OPERATION (Continued)2.3.2. STARTING WHEEL DRIVE1. Shift speed control lever to neutral.2. Start engine. Refer to Section “STARTINGENGINE”.3. Release clutch/brake pedal.4. Slowly shift speed control lever forward forforward motion or to the rear for reverse motion. SeeFigure 2.7.SPEED CONTROL LEVER2.4 STOPPING ENGINE, BLADE, WHEEL DRIVE2.4.1. STOPPING ENGINE1. Stop engine by turning key to the "OFF" position.See Figure 2.9.OFFRUNSTARTNEUTRALREVERSEKEYFORWARDSPEEDSFIGURE 2.7FIGURE 2.92.4.2. STOPPING WHEEL DRIVE1. Fully depress clutch/brake pedal to stop wheeldrive. See Figure 2.10.2.3.3 STARTING MOWER BLADE1. Start engine. Refer to Section “STARTINGENGINE”.2. Pull blade switch OUT to engage blade. SeeFigure 2.8.PUSH BLADE SWITCH IN TOTHE “OFF” POSITIONONCLUTCH/BRAKEPEDALOFFPULL BLADESWITCH OUT TOTHE “ON”POSITIONFULLY DEPRESSCLUTCH/BRAKE PEDAL TOSTOP WHEEL MOTIONFIGURE 2.10FIGURE 2.8WARNINGDO NOT operate blades in reverse. STOP BLADES.LOOK and SEE behind and down for children, petsand hazards before and while backing.8
Section 2 - OPERATING INSTRUCTIONS2.4 STOPPING2.4.3. STOPPING MOWER BLADES1. Stop mower blade by pushing blades switch IN todisengage blades. See Figure 2.11.2.4.5. RELEASING PARK BRAKE1. Fully depress clutch/brake pedal. Move park brakelever “DOWN” to release park brake. Releaseclutch/brake pedal. See Figure 2.13.PUSH BLADE SWITCH IN TOTHE “OFF” POSITIONONCLUTCH/BRAKEPEDALPARKBRAKELEVEROFFPULL BLADESWITCH OUT TOTHE “ON”POSITIONFULLY DEPRESSCLUTCH/BRAKEPEDALFIGURE 2.11WARNINGOnce blades are disengaged, they should come to acomplete stop in 5 seconds or less. If the bladescontinue to rotate after 5 seconds, the blade brakemust be repaired. Return machine to an authorizedSNAPPER dealer. DO NOT continue to operatemachine until blade brake has been repaired andfunctioning properly.2.4.4. SETTING PARK BRAKE1. Fully depress clutch/brake pedal.2. Move park brake lever up into slot. See Figure 2.12.3. Release pedal.FIGURE 2.132.5. CUTTING HEIGHT ADJUSTMENT1. Depress lock button on cutting height adjustmentlever. See Figure 2.14.DEPRESSLOCK BUTTONCUTTINGHEIGHTADJUSTMENTLEVERPUSH PEDAL ALLTHE WAY DOWNPARK BRAKELEVERHIGHEST CUTFIGURE 2.14LOWEST CUT2. Raise or lower deck to any of six positions asdesired. Release lock button.MOVE PARK BRAKELEVER “UP” TOENGAGE PARK BRAKEWARNINGDO NOT park machine on slopes.FIGURE 2.129
Page 6 and 7: Section 2 - OPERATING INSTRUCTIONS2
Page 11 and 12: Section 2 - OPERATING INSTRUCTIONS2
Page 13 and 14: Section 3 - MAINTENANCE3.2.4. CHECK
Page 15 and 16: Section 3 - MAINTENANCE3.4 ANNUALLY
Page 17 and 18: Section 4 - ADJUSTMENT & REPAIRWARN
Page 33 and 34: Section 4 - ADJUSTMENT & REPAIRAVAI
Page 35 and 36: TROUBLESHOOTING GUIDEPROBLEM PROBAB
Page 37 and 38: MAINTENANCE SCHEDULESUBJECTSERVICER
Page 39 and 40: PRIMARY MAINTENANCE39
Page 41 and 42: PRIMARY MAINTENANCE41
Page 43 and 44: SERVICE NOTES______________________

Snapper Lawn Tractor Hydrostatic Drive Electric Clutch Series G ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?