Installation, Operation & Maintenance Manual - Acme Fluid Handling

More documents

Recommendations

Info

Appendix AVertical Single-Acting Model Number Identification CodeBase Model 91 291 491 691Inlet 3/4” NPT 3/4” NPT 1-1/4” NPT 2” NPTModel NumberBase X X X X X X X X X XOutlet 3/4” NPT 3/4” NPT 1-1/4” NPT 1-1/2” NPTBase Model F91 F291 F491 F691Inlet 3/4” ANSI 3/4” ANSI 1-1/4” ANSI 2” ANSIOutlet 3/4” ANSI 3/4” ANSI 1-1/4” ANSI 2” ANSIPacking Arrangement Pressurized inlet Standard ACrankcase StyleValvesSplash lubricated Standard N/A N/A N/A JExtended crankshaft Extra cost Extra cost Extra cost N/A EPressure lubricated N/A Standard Standard Standard MStandard with heater N/A Extra cost Extra cost Extra cost MHLiquid relief suction Standard 3Standard valves No extra cost 4Piston Rings and PackingPTFE Standard FAlloy 50 Extra Cost GAluminum Standard BGasket Material Copper No extra cost CLead-iron No extra cost DO-rings Buna-N Standard ANeoprene ®1 No extra cost BViton ®1 Extra cost DTeflon ®1 Extra cost EIntercooler None N/A for single stage compressor N14” flywheel used withextended crankshaftNo charge N/A EFlywheel Heavy duty Extra cost Extra cost Extra cost Extra cost HNo flywheel No extra cost NStandard 14” Standard SProtective Coating No coating Standard NPiston Rod CoatingNitrotec Standard NChrome oxide Extra cost C1 Teflon ® , Neoprene ® , and Viton ® are registered trademarks of the DuPont company.See Appendix C for mounting options.26
Appendix AVertical Single-Acting Model Number Identification CodeBase Model NumberD891Inlet Connection2” WeldOutlet Connection2” WeldShip Weight (lb) 900Model NumberBase X X X X X X X X X XPackingArrangementPacking arranged for padding of distance piece Standard JCrankcase Pressure lubricated Standard MStyle Standard with heater Extra cost MHValvesStandard suction and discharge valves Standard 4Suction valve unloaders Extra cost 9Piston Ringand Packing Teflon ®1 Standard FMaterialGasket Material Aluminum Standard BO-ring Buna-N Standard AMaterial Neoprene ®1 No charge BIntercooler N/A for single stage compressor Standard NFlywheel No flywheel provided No charge NStandard flywheel Standard SProtectiveCoatingNone Standard NPiston RodCoatingNitrotec Standard N1 Teflon ® and Neoprene ® are registered trademarks of the DuPont company.Mounting Selections103 Mounting includes: Steel baseplate, adjustable driver slide base, V-belt drive and enclosed steel belt guard. Pressure gauges aremounted on the compressor. 3107 Mounting includes: Steel baseplate, mechanical liquid trap, non-lube 4-way valve, interconnecting piping, strainer, adjustable driver slidebase, V-belt drive and enclosed steel belt guard. Pressure gauges are mounted on the compressor.107A Mounting includes: All items on the 107 replacing the mechanical float in the liquid trap with a NEMA 7 liquid level switch.107B Mounting includes: All items on the 107 replacing the liquid trap with a larger ASME code liquid trap with 2 NEMA 7 liquid levelswitches set for alarm and shutdown.107TR Mounting includes: All items on the 107 set up to be used as a transport unit. Note that the compressor must have the optional 14”flywheel and extended crankshaft to use this mounting. 2109 Mounting includes: Steel baseplate, mechanical liquid trap, interconnecting piping, adjustable driver slide base, V-belt drive andenclosed steel belt guard. Pressure gauges are mounted on the compressor. 3109A Mounting includes: All items on the 109 replacing the mechanical float in the liquid trap with a NEMA7 liquid level switch. 3109B Mounting includes: All items on the 109 replacing the liquid trap with a larger ASME code liquid trap with 2 NEMA 7 liquid levelswitches set for alarm and shutdown. 3109TR Mounting includes: All items on the 109 set up to be used as a transport unit. Note the compressor must have the optional 14”flywheel and extended crankshaft to use this mounting. 2,32 Not suitable for 691.3 Discharge relief valves are required but not included in these mountings.27
Page 5 and 6: this by withdrawing vapors from the
Page 7 and 8: Corken’s automatically reversible
Page 10 and 11: 2.4 Liquid TrapsCompressors are des
Page 12 and 13: 2.5 Driver Installation / Flywheels
Page 14 and 15: Chapter 3—Starting Up Your Corken
Page 16 and 17: Chapter 4—Routine Maintenance Cha
Page 18 and 19: Disassembly1. Unscrew the valve cap
Page 20 and 21: of damage to cylinders is corrosion
Page 22 and 23: 5. Push down on washer and insert r
Page 24 and 25: 5.9 Servicing the Four-Way ValveUnl
Page 28 and 29: Appendix B—Vertical Single-Acting
Page 34 and 35: Appendix C—Compressor SelectionCo
Page 36 and 37: Appendix C—Compressor SelectionPr
Page 38 and 39: Appendix D—Outline DimensionsMode
Page 42 and 43: AUTOMATIC LIQUID TRAPLIQUID LEVEL S
Page 50 and 51: Appendix F—91 and F91 Head and Va
Page 52 and 53: Appendix F—91 and F91 Piston Asse
Page 54 and 55: Appendix F—91 and F91 Connecting
Page 56 and 57: Appendix F—91 and F91 Crankcase A
Page 58 and 59: Appendix G—291 and F291 Head and
Page 60 and 61: Appendix G—291 and F291 Piston As
Page 62 and 63: Appendix G—291 and F291 Connectin
Page 64 and 65: Appendix G—291 and F291 Crankcase
Page 66 and 67: Appendix H—490, 491, and F491 Hea
Page 68 and 69: Appendix H—490, 491, and F491 Pis
Page 70 and 71: Appendix H—490, 491, and F491 Con
Page 72 and 73: Appendix H—490, 491, and F491 Cra
Page 74 and 75: Appendix I—691 and F691 Head and
Page 76 and 77:
Appendix I—691 and F691 Piston As
Page 78 and 79:
Appendix I—691 and F691 Connectin
Page 80 and 81:
Appendix I—691 and F691 Crankcase
Page 82 and 83:
Appendix J—D891 Head and Valve As
Page 84 and 85:
Appendix J—D891 Crosshead Guide A
Page 86 and 87:
Appendix J—D891 Connecting Rod As
Page 88 and 89:
Appendix J—D891 Crankcase Assembl
Page 90:
CORKEN, INC. • A Unit of IDEX Cor
show all

Installation, Operation & Maintenance Manual - Acme Fluid Handling

Create successful ePaper yourself

Delete template?

Save as template?