ToneLab EX Owner's Manual - Vox

More documents

Recommendations

Info

Panel Tour � (Top and rear panels) 2 Here we’ll introduce you to the switches, controls, and con‐ nections on the ToneLab EX’s top panel. Top panel 1 2 3 4 5 6 7 8 9 1.Amp section Here youʹll create settings for the amp model and stand alone pedal. For details on each effect, refer to “Amp models” (p. 15) and “stand alone pedals” (p. 22). NOTE: You cannot use the amp model and stand alone pedal simultaneously. If you turn one of them on, the other will turn off. a b c d e f g h a. AMPS bank select switch and LED Use this to switch the bank, or to turn the amp model on/off. Each time you press the switch, the bank will cycle between STANDARD, SPECIAL, CUSTOM, STANDARD... The color of the LED will indicate the bank that’s selected. •STANDARD: green •SPECIAL: orange •CUSTOM: red The LED will be lit‐up if the amp model is on. By holding down this switch for about one second you can switch the amp model on/off.
. STAND ALONE PEDALS switch and LED Use this to turn the stand alone pedal on/off. The LED will be lit‐up if the stand alone pedal is on. c. CABINET ON/OFF switch and LED This turns the cabinet model on/off. The LED will be lit if the cabinet model is on. By entering the OPTION parameter setting mode you can set parameters for the cabinet model. The OPTION parameter setting mode To enter the OPTION parameter setting mode, hold down the CABINET ON/OFF switch for about one second. You’ll be in The OPTION parameter setting mode, and the LED will blink. The OPTION parameter setting mode lets you adjust the fol‐ lowing settings. • GAIN control: cabinet model (CABINET SELECT) • TREBLE control: presence (PRESENCE) • MIDDLE control: noise reduction (NR) • BASS control: Total Equalizer High (EQ HI) • REVERB control: Total Equalizer Low (EQ LO) • VOLUME control: Trim (TRIM) To return to the previous operation, press the CABINET ON/ OFF switch or the EXIT/TUNE switch. NOTE: Total Equalizer is enabled only when the AMP/LINE switch is set to LINE. NOTE: Presence is effective only when the amp model or the stand alone pedal is turned on. d. AMPS/STAND ALONE PEDALS selector This selects the amp model or the stand alone pedal. The type you select will determine the response of the gain circuit and tone controls, and the order in which they are located in the circuit. If the amp model and stand alone pedals are turned off, rotating this selector will turn the amp model or stand alone pedal on. e. GAIN control This adjusts the gain of the selected amp model or stand alone pedal. In the OPTION parameter setting mode, this control selects the cabinet model. If the cabinet model is turned off, turning this control in the OPTION parameter setting mode will turn the cabinet model on. f. TREBLE, MIDDLE, BASS controls These adjust the tone of the high, mid, and low frequency ranges. The way these controls affect the tone will depend on the model you’ve selected. NOTE: Depending on the selected amp model, there may be almost no sound if you turn all three of these controls to the far left. In the OPTION parameter setting mode, the TREBLE control adjusts the presence, the MIDDLE control adjusts the noise reduction, and the BASS control enables you to adjust the Total Equalizer High. g. REVERB knob Depending on the position of the knob, this selects the reverb type (SPRING, ROOM, or HALL), and adjusts the amount of 3
Page 2 and 3: Precautions ii Location Using the u
Page 4 and 5: Contents iv Introduction ..........
Page 8 and 9: 4 reverb in the mix. If you turn th
Page 10 and 11: . MODULATION selector This selects
Page 12 and 13: Rear panel 8 1 2 3 4 5 6 7 8 9 10 1
Page 14 and 15: 10 2. Use a cable to connect the To
Page 16 and 17: Creating your own sounds Creating a
Page 18 and 19: Noise reduction settings 14 Noise r
Page 20 and 21: 1. CLEAN STANDARD This models the c
Page 22 and 23: 18 SPECIAL Designed after our VOX H
Page 24 and 25: Cabinet models 20 These simulate th
Page 26 and 27: stand alone pedals 22 The ToneLab E
Page 28 and 29: Pedal 2 24 Like stand alone pedals,
Page 30 and 31: 26 HINT: Parameters that can be ass
Page 32 and 33: 11.TALK MOD This is an envelope con
Page 34 and 35: 30 4. When you’ve finished tuning
Page 36 and 37: 32 To assign volume, gain, or the i
Page 38 and 39: Adjusting the sensitivity of the ex
Page 40 and 41: Restoring the factory settings 36 H
Page 42 and 43: Song Preset Program List 38 26 27 2
Page 44: © 2010 VOX AMPLIFICATION LTD.

ToneLab EX Owner's Manual - Vox

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?