35401.1 PKZ Archer RTF BNF manual.indb - Robot MarketPlace

More documents

Recommendations

Info

ENServo Reversing Switches (K)These switches select the servo direction of each channel. Use your fi ngernailor a small screwdriver to change the switch position to normal (NOR) orreverse (REV) as needed to make transmitter controls operate the model asdesired. Perform the Control Direction Test before fl ying.ACT/AUX Switch (Q)This switch activates a receiver channel (such as servos) connected throughan AUX channel of the receiver.France RF SettingThe DX4e has a France RF setting that complies with French regulations. TheFrance RF setting should only be turned on when operating your transmitter inFrance outdoors.1To set France mode (Illustration 1 below):Push and hold the trainer button on the top of the transmitter while pushingand holding the two sticks as shown below, then power ON the transmitter.After hearing a series of descending beep tones (high to low), release thetrainer switch and the sticks. The France setting is now turned on. Bind thetransmitter to the receiver for the change to take effect.To set Standard mode (Illustration 2 below):Push and hold the trainer button on the top of the transmitter while pushingand holding the two sticks as shown below, then power ON the transmitter. Afterhearing a series of ascending beep tones (low to high), release the trainerswitch and the sticks. The France setting is turned off.2DX4e Range CheckPlacing the transmitter in RANGE CHECK mode reduces the output power,allowing a range check.DX4e Transmitter Range Check ProcessBefore performing the range check, ensure the correct failsafe stickpositions are established.1. With the system powered on and the model restrained on theground*, stand 90ft/28m away from the model.2. Face the model with the transmitter in your normal fl ying position.3. Push and hold the trainer button while toggling the Hi/Lo Rate Switchfour times.4. The LEDs will fl ash and the alarm will sound. The system is in rangecheck mode.IMPORTANT: You must hold the trainer button during the entire rangecheck process. Releasing the button switch will exit the range checkmode.You should have total control of the model with the trainer button held at90ft/28m meters.28 meters (90 feet)*In some aircraft, when the model is placed on the ground, the antenna(s)can be within inches of the ground. Close proximity of the antenna(s) to theground can reduce the effectiveness of the range check. This is called pulling.If you experience issues during the range check, restrain the model on a nonconductivestand or table up to 2ft (60cm) above the ground. Then range checkthe system again.If control issues exist, contact the appropriate Product Support Department forassistance, or visit the Spektrum website for more information.6
ENTransmitter and Receiver BindingBinding is the process of programming the receiver to recognize the GUID (Globally Unique Identifi er) code of a single specifi c transmitter. You need to ‘bind’ yourchosen Spektrum DSM2 ® /DSMX ® technology equipped aircraft transmitter to the receiver for proper operation (Please visit www.bindnfl y.com for a complete listof compatible transmitters).CAUTION: When using a Futaba ® transmitter with a Spektrum DSM ® module, you must reverse the throttle channel and rebind. Refer to your Spektrummodule manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.Binding Procedure Reference Table (RTF Version: Your Spektrum DX4e comes prebound to the aircraft.)1. Read the transmitter instructions for binding to a receiver (location of transmitter’s Bind control).2. Make sure the transmitter is powered OFF.3. Move the transmitter controls to neutral (fl ight controls: rudder, elevators and ailerons) or to lowpositions (throttle, throttle trim).*BIND PLUG4. Install a bind plug in the receiver bind port.5. Connect the fl ight battery to the ESC. The ESC will produce a series of sounds. One long tone,then two short tones confi rm that the LVC is set for the ESC.6. The receiver LED will begin to fl ash rapidly.7. Power ON the transmitter while holding the transmitter bind button or switch. Refer to yourtransmitter’s manual for binding button or switch instructions.For the DX4e, release the trainer/bind button once the LEDs fl ash and a series of beeps sound.Within a few seconds, the system should connect.8. When the receiver binds to the transmitter, the light on the receiver will turn solid and the ESCwill produce a series of three ascending tones. The tones indicate the ESC is armed, providedthe throttle stick and throttle trim are low enough to trigger arming.9. Remove the bind plug from the bind port.10. Safely store the bind plug (some owners attach the bind plug to their transmitter using two-partloops and clips).11. The receiver should retain the binding instructions received from the transmitter until anotherbinding is done.* The throttle will not arm if the transmitter’s throttle control is not put at the lowest position. If you encounter problems, follow the binding instructions andrefer to the transmitter troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Product Support offi ce.Installing the Battery1. Push the antenna (A) into the fuselage, releasing the canopy latch.A2. Lift the back of the canopy and pull backwards to remove the canopy.3. Install the fully charged battery (B) in the battery compartment. See theAdjusting the Center of Gravity instructions for more information.4. Make sure the fl ight battery is secured using the hook and loop strap (C).5. Reinstall the canopy. Push the rear of the canopy securely to ensure thelatch is fully engaged.BC7
Page 1 and 2: ArcherInstruction Manual / Bedienun
Page 3: - Introduction -As you’re about t
Page 8 and 9: ENArming the ESC and ReceiverArming
Page 10 and 11: ENInstalling the Wing1. Remove the
Page 12 and 13: ENControl Direction TestMove the co
Page 14 and 15: ENRemoving the Nose GearNose Gear S
Page 16 and 17: ENTroubleshooting GuideProblem Poss
Page 18 and 19: ENFCC InformationOperation is subje
Page 20 and 21: Optional Parts • Optionale Bautei

35401.1 PKZ Archer RTF BNF manual.indb - Robot MarketPlace

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?